OWL F7BMS MM Operation Manual Download Page 54

Page: 54 / 60

OPERATIONS/MAINTENANCE

SETUP MENU > POWER OPTIONS

-- Set duration for various power saving modes

DIM TIME

minutes before display dims

Range of values: 1 to 250

STANDBY TIME

minutes before unit goes into standby mode (only display turns off)

Range of values: 2 to 250

OFF TIME

minutes before unit turns completely off

Range of values: 3 to 250

SAVE

Save settings and return to SETUP MENU

EXIT

Exit without saving settings and return to SETUP MENU

HELP

Context-sensitive help

SETUP MENU

POWER OPTIONS

DIM TIME:

STANDBY TIME:

OFF TIME:

Times in minutes

(0 = disable)

SAVE

EXIT

HELP

SETUP MENU > CUSTOM STANDARD

-- configure a custom standard with user-definable standard

parameters. Parameters are set for each fiber type.

FIBER TYPE

Options: 62.5um OM1 / 50.0um OM2 / 50.0um OM3 / 50.0um OM4

Indoor SM / Outdoor SM

Select a fiber type and press EDIT to set parameters for that fiber type.

Wave (nm)

Up to 2 wavelengths (column A and B) can be defined per fiber type

Options: 850, 980, 1300, 1310, 1490, 1550, 1625, 0

Two types of standards can be defined:

GENERIC STANDARDS (link budget is calculated based on link configuration)

uses Loss/km, Max len, Con loss, and Spl loss

APPLICATION STANDARDS (link budget is a fixed number)

uses Max loss, Min loss, and Max len

GENERIC STANDARD PARAMETERS

Loss/km (dB)

Amount of acceptable dB loss (attenuation) per kilometer of fiber

Max len (m)

Maximum length of fiber link in meters

Con loss (dB)

dB loss per interconnection; defines both reference-grade and standard-grade reference cable connectors

Spl loss (dB)

dB loss per splice; can be either fusion or mechanical splices

APPLICATION STANDARD PARAMETERS

Max loss (dB)

loss measurements that exceed Max loss will show as a FAIL

Min loss (dB)

loss measurements that do not reach the Min loss will show as a FAIL

Max len (m)

Maximum length of fiber link in meters

62.5um OM1

EDIT

EXIT

HELP

SET CUSTOM STANDARD

FIBER TYPE

850 1300

3.50 1.50

0.00 0.00

90 90

EDIT

EXIT

HELP

62.5um OM1

Wave

(nm)

Loss/km

(dB)

Max loss

(dB)

Min loss

(dB)

Max len

(m)

Con loss

(dB)

Spl loss

(dB)

0.30 0.75

0.30

Reference Standard

Summary of Contents for F7BMS MM





























































Search results

Summary of Contents for F7BMS MM

Reviews:

Related manuals for F7BMS MM

Brands by name

Popular brands

OWL F7BMS MM, Operation Manual

Search results

Summary of Contents for F7BMS MM

Reviews:

Related manuals for F7BMS MM

Brands by name

Popular brands