OWL F7BMS MM Operation Manual Download Page 28 | Manualshive

Page: 28 / 60

background image

28

REQUIRED ACCESSORIES

REFERENCE CABLES (2 each): used to set references (aka “zeroing”), and connect the light source (transmit) ports into the link

during testing. Each test unit includes a transmit port and receive port, thus the need for 2 cables.

Please note whether these reference cables are standard-grade or reference-grade.

There are five different types of reference cables that could be used, depending upon the fiber type of the link under test and the

test parameters:

REFERENCE CABLES AND MANDRELS

SINGLEMODE

62.5/125 (OM1)

Mandrel-wrapped

50/125 (OM2/3/4)

Mandrel-wrapped

50/125 (OM2/3/4)

Encircled Flux (EF)

62.5/125 (OM1)

Encircled Flux (EF)

NOTE: EF cables are always considered

as reference-grade.

0.7” diameter

0.9” diameter

«
...
26
27
28
29
30
...
»

Summary of Contents for F7BMS MM





























































Reviews:

No comments

Related manuals for F7BMS MM

Brand: R&S Pages: 733

Brand: R&S Pages: 369

Brand: Flytec Pages: 2

Brand: X-laser Pages: 17

Brand: KALEAS Pages: 64

Sensorex SX41170SI

Brand: Meggitt Pages: 19

Speedrite Fault Finder

Brand: Tru-Test Pages: 2

KINGFISHER PLUS+

Brand: semaphore Pages: 247

Brand: Ratek Pages: 24

Brand: Oldham Pages: 106

Brand: E Instruments Pages: 2

Brand: Michell Instruments Pages: 28

Brand: 3nh Pages: 39

Brand: ICP DAS USA Pages: 71

Brand: CONDTROL Pages: 11

Brand: Milwaukee Pages: 17

AcuRev 1310 Series

Brand: AccuEnergy Pages: 109

Brand: BANTE Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands