background image

72.

Attach 

Filler

Trims 

(2 - 1/2” x 2

1/2” x 75”) to rear
walls. Hammer with 
8 - 1 1/4” finishing
nails. Trims are 
positioned flush with
siding and bottom
skirting.

70.

Attach 

Bottom Skirting

around the base of the shed.
Skirting will hide floor framing.
The front skirting pieces will
overlap the side skirting. Start
with side skirting for porch.
Attach with 4 - 1 1/4” finishing
nails per piece.  The skirting
will sit flush with the outside
deck board. The middle and
end side skirting pieces will sit
flush under siding of wall panel.

3 pieces of Bottom Side
Skirting per side.

Side Skirting for Deck

Front Overhangs
Side Skirting

Flush

Rear

Skirting

Side

Skirting

Gap at rear

Toll Free 1-888-658-1658             www.outdoorlivingtoday.com          [email protected]

Page 28

Filler Trim

Attach

additional 1 1/4” screws

on bottom edge of wall siding

into bottom wall plate to further

secure bottom siding to framing.

Drill pilot holes in siding to

prevent splitting.

71.

There are 2 Front

Skirting Pieces that are 48
1/2” long. Use 6 finishing
nails on both front skirting
pieces for extra support
since it will be a high traffic
area.

Summary of Contents for Santa rosa



































Reviews: