SECTION 3 - CHASSIS & TURNTABLE
3120740
– JLG Lift –
3-75
3.17
SWING BRAKE (S/N 0300068040 TO
S/N 0300183033)
Disassembly
1.
Remove pressure plate (2) from cover (16) by removing
washer head cap screws (1).
PRESSURE PLATE IS UNDER SPRING TENSION OF APPROXIMATELY 907 KGF
(2000 LBS.) THE TWO WASHER HEAD CAP SCREWS MUST BE LOOSENED
EVENLY TO RELIEVE THIS FORCE. IF A HYDRAULIC PRESS IS AVAILABLE, 1361
KGF (3000 LBS.) MINIMUM, THE PRESSURE PLATE CAN BE HELD IN POSITION
WHILE REMOVING THE WASHER HEAD CAP SCREWS.
2.
Remove case seal (3) from cover (16).
3.
Remove piston (6) from pressure plate (2).
4.
Remove o-ring (4), back-up ring (5), o-ring (7) and back-
up ring (8) from piston (6).
5.
Remove stack assembly, consisting of stator disc (10),
rotor disc (11) and return plate (12) from cover (16).
6.
Remove dowel pins (15), springs (13) and spring retainer
(14) from cover (16).
NOTE:
Not all models use the same number of springs or spring
pattern. Record this information for assembly purposes.
7.
Remove retaining ring (19) from cover (16).
8.
Remove shaft by pressing or using a soft mallet on the
male end of the shaft (9).
9.
Remove retaining ring (20) from cover (16) and press out
oil seal (17) and bearing (18) if required.
Assembly
NOTE:
Lubricate all rubber components from repair kit with clean
type fluid used in the system
1.
Use an alkaline wash to clean parts before assembly.
2.
Press oil seal (17) into cover (16) until it is flush with
bearing shoulder. Note direction of seal.
3.
Press bearing (18) into position until it bottoms out on
borestep.
4.
Install retaining ring (20) in cover (16).
5.
Press shaft (9) into bearing (18) until it bottoms on the
shoulder. Bearing (18) inner race must be supported
during this operation.
6.
Install retaining ring (19) on shaft (9).
7.
Insert dowel pins (15), spring retainer (14) and springs
(13) in cover (16).
NOTE:
Be sure to use the same number of springs and the same
spring pattern as recorded during disassembly.
8.
Position plate (12) on spring (13).
NOTE:
Discs (10 & 11) and plate (12) must remain dry during
installation. No oil residue must be allowed to contami-
nate disc surfaces.
9.
Install rotor disc (11) and stator disc (10).
10.
Install o-ring (4), back-up ring (5), o-ring (7) and back-up
ring (8) on piston (6). Note order of o-rings and back-up
rings. Insert piston (6) into pressure plate (2).
NOTE:
Be careful not to shear o-rings or back-up rings. Be careful
not to scratch or mar piston.
11.
Install new case seal (3) in cover (16).
12.
Position pressure plate (2) on cover (16) aligning dowel
pins (15) with holes in pressure plate.
13.
Install washer head cap screws (1) and tighten evenly to
draw pressure plate (2) to cover (16). Torque washer
head capscrews 55 ft. lbs. (75 Nm).
NOTE:
A hydraulic press will simplify installation of pressure plate
on cover. Clamp pressure plate in position while tightening
the washer head cap screws.
IF HYDROSTATIC BENCH TESTING IS PERFORMED ON THE BRAKE ASSEMBLY,
RELEASE PRESSURE MUST NOT EXCEED 137.9 BARS (2000 PSI) UNLESS TWO
ADDITIONAL BOLTS ARE USED FOR SUPPLEMENTAL CLAMPING.
Go to
Discount-Equipment.com
to
order your
parts
