Orion OPM-4250, User Manual

Page: 37 / 45

- 70 -
OPM-4250 | OPM-4250R
- 71 -
Infinitely Expandable
"Get"commandfrom"Get/Set"in"Data"area B.
STX CMD Length
Data
ETX
ID M/S Setting Values
Value 0x02 0x6A 0x05 Variable Variable … 0x03
Value bit Get/Set Address
Variable 0x01 Variable
*IDrange(Program):0x01(1)~0xFF(255)
*M/S:SinceitisonlyMaster,"0x01"Valuemustbetransmitted.
*SettingValues
-Valuebit: Areaforsetting8,16,and32bit.Currently,32bitsettingisused.(8bit:0x01/16bit:0x02/32bit:0x04)
-Get/Set: Readorwritedatainadesignatedaddress.(Get:0x01,Set:0x00)
-Address: TheaddressintheinternalregisterofBICmodule.
-Value:
Thelengthofdatacanbevariableaccordingtothesettingsof"Valuebit"area.Currently,32bitdataisused.
*Broad-cast:AllPDP(OnlyMaster)setswillexecutethesamecommand,whentheIDis0x00.Noresponse(Onewaycommand)
"Get"commandfrom"Get/Set"in"Data"areaisapplied,"Broad-cast"commandcannotbeexecuted.
Receive from MPDP -
Responsefor"Set"commandfrom"Get/Set"in"Data"area A.
STX CMD Length
Data
Check Sum ETX
ID M/S
Value 0x02 0x6A 0x02 Variable 0x01 Variable 0x03
*IDrange(Program):0x01(1)~0xFF(255) *M/S:SinceitisonlyMaster,"0x01"Valuemustbetransmitted.
*CheckSum:Execute"Not"operationafteraddingallthevaluesin"STX~Data"area.
Responsefor"Get"commandfrom"Get/Set"in"Data"area B.
STX CMD Length
Data
ETX
ID M/S Setting Values
Value 0x02 0x6A 0x09 Variable Variable … 0x03
Value bit Get/Set Address Value
Variable Variable Variable …
Value3 Value2 Value1 Value0
Variable Variable Variable Variable
*IDrange(Program):0x01(1)~0xFF(255) *M/S:SinceitisonlyMaster,"0x01"Valuemustbetransmitted.
*GettingValues
-Valuebit: Areaforsetting8,16,and32bit.Currently,32bitsettingisused.(8bit:0x01/16bit:0x02/32bit:0x04)
-Get/Set: Responsefor"Get"is"0x01."
-Address: TheaddressintheinternalregisterofBICmodule.
-Value:
Thelengthofdatacanbevariableaccordingtothesettingsof"Valuebit"area.Currently,32bitdataisused
*CheckSum:Execute"Not"operationafteraddingallthevaluesin"STX~Data"area.
"BIC" Communication Sequence -
*Waitfor1000msecforresponseaftersending"Get,"40msecfor"Set"commands.Ifthereisnoresponse,itisrecommendedto
resendthecommand.
*Itisrecommendedthatnotsendingtheothercommandorchanginginputresolutionduringcommandtransmission.
BIC Command transmission (to Master)
→
←
BIC Response transmission (from Master)
graphic User Mode Control 3.15.
Command for controlling Brightness, Contrast, Sharpness, Color and Tint -
CMD: 0x8A (Brightness), 0x8B (Contrast), 0x8C (Sharpness) -
It is available only on Power On (Operative) status. -
The adjusted value is not applied during Stand-by or No-signal status. MPDP must be operating status and
-
there must be the input signal of each mode.
Send to MPDP
-
NormalCommand A.
STX CMD Length
Data
ETX
ID M/S Value
Value 0x02 Variable 0x03 Variable Variable Variable 0x03
*IDrange(Program):0x01(1)~0xFF(255)
*M/S:Master(0x01),Slave(0x00)
*Value:
-GeneralInputMode:Brightness("0"~"100"),Contrast("0"~"100"),Sharpness("0"~"28")
BroadcastCommand B.
STX CMD Length
Data
ETX
ID Value
Value 0x02 Variable 0x02 Variable Variable 0x03
*MakeallPDP(Master/Slave)dothesameoperation.But,therewillbenoreturncommunication.(Onewaycommand)
*Value:
-GeneralInputMode:Brightness("0"~"100"),Contrast("0"~"100"),Sharpness("0"~"28")
Receive from MPDP
-
STX CMD Length
Data
Check Sum ETX
ID M/S
Value 0x02 Variable 0x02 Variable Variable Variable 0x03
*IDrange(Program):0x01(1)~0xFF(255)
*M/S:Master(0x01),Slave(0x00)
*CheckSum:Execute"Not"operationafteraddingallthevaluesin"STX~Data"area.
"Graphic User Mode Control" Communication Sequence -
*Waitfor40msecforresponseaftersendingthecommand.Ifthereisnoresponse,itisrecommendedtoresendthecommand.
*Itisrecommendedthatnotsendingtheothercommandorchanginginputresolutionduringcommandtransmission.
*ExceptforBroadcastcommand
Graphic User Mode Control Command transmission
(to Master or Slave)
→
←
Graphic User Mode Control Response transmission
(from Master or Slave)
White Balance Control 3.16.
Command for adjusting Gain R/G/B and Offset R/G/B for White balance -
CMD: 0xAC (Gain R), 0xAD (Gain G), 0xAE (Gain B), 0xB0 (Offset R), 0xB1 (Offset G), 0xB2 (Offset B) -
The adjusted value is not applied during Stand-by or No-signal status. MPDP must be operating status and -
there must be the input signal of each mode.
To apply the same configuration to all MPDP sets, the "ID" area value can be set as "0x00." However, considering
-
differences between sets, individual adjustment for white balance is recommended.