Orbitalum RA 41 Plus Operating Instructions Manual Download Page 30 | Manualshive

Page: 30 / 40

background image

7 Operation

Operating instructions RA 41 Plus (H)

26

(07.08)

MT_RA 41 Plus (H)_BA_04_790046773_04.doc

orbitalum tools

gmbh

7.6.1

Bevel correction (only at saw position 1)

The size of the bevel can be increased by:

If the bevel of the cutter is wide enough.

X

The cutter moves further into the pipe wall and the bevel is larger.

1. Release the clamping lever (1).

2. Move the stop (2) to the right.

3. Switch the motor on.

4. Using the grip, turn the motor carefully in a clockwise direction until the

bevel cutter engages.

5. Continue to turn smoothly until the pipe has been beveled and the

markings on the rotary element and housing are in line.

6. Switch the motor off.

If the cutter does not have a very wide bevel.

X

The bevel will be larger for the same setting.

Advancing the cutter:

Sliding the tube

further into the vice:

«
...
28
29
30
31
32
...
»

Summary of Contents for RA 41 Plus









































Reviews:

No comments

Related manuals for RA 41 Plus

Brand: SafetySpeed Pages: 43

Brand: National Instruments Pages: 15

Brand: V-TAC Pages: 16

Brand: MGS Pages: 38

Brand: Delta Electronics Pages: 13

Brand: Roebuck Pages: 16

Brand: Freeman Pages: 19

Brand: Ryobi Pages: 24

Brand: Maestri Pages: 16

Brand: YATO Pages: 112

Akku-Press 22 V ACC

Brand: REMS Pages: 212

Brand: Enerpac Pages: 16

Brand: Elektro-Automatik Pages: 4

Brand: OEM Tools Pages: 8

Brand: Neilsen Pages: 2

Brand: YATO Pages: 64

Brand: Far Tools Pages: 17

Brand: Performance Tool Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands