11
Using your iOsense™ charger
Personalized live-coaching and
Smart Pressure Sensor features
The iOsense™ charger has a built-in real-time feed-
back on brushing coverage, brushing time and
pressure. The LED lights on top of your iOsense™
charger illustrate your upper and lower jaw (a). You
may start your brushing session at any area of your
mouth. While the area is being brushed, the
respective light fades from blue to white, indicating
the brushing progress. Once one area is cleaned
(a), the respective LED turns into white.
If too much pressure is applied, LEDs light up in red
reminding you to reduce pressure (e).
Caution: During a brushing session with enabled
brushing recognition feature on your iOsense™
charger, please stay within 5m distance to your
iOsense™ charger to ensure a stable connection
and brushing recognition.
To enable the full feature set of iOsense™ charger,
the Oral-B App is required. Please follow the
instructions in the Oral-B App for connection setup.
Clock setup
Launch the Oral-B App and connect the iOsense™
charger with your Wi-Fi by following the instructions
in the Oral-B App.
Note: The clock doesn’t work without the Wi-Fi
connection.
Bluetooth
& Wi-Fi
®
functions
The iOsense™ charger supports
Bluetooth
and
Wi-Fi.
•
Bluetooth
connects the iOsense™ charger with
the toothbrush and the Oral-B App.
•
Wi-Fi connects the iOsense™ charger with the
internet.
iOsense™ button functions
You may find the capacitive touch button (d) on the
back of your iOsense™ charger. It has two functions:
•
Low Power Mode:
Device enters into low power
mode. All features beyond charging are disabled.
Tap the button (d) twice to enable low power
mode and once to disable. The activation of low
power mode is indicated by the LEDs on the top
of your iOsense charger. Power consumption of
networked standby mode: 1,2 W.
•
Factory reset:
Touch and hold the button (d)
until orange light appears on the top of your
iOsense™ charger, then release the button. Tap
the button once again while orange light is on,
to trigger the factory reset. LEDs spin orange
clockwise to confirm the factory reset. All
credentials and settings are deleted from the
iOsense™ charger.
Cleaning recommendations
After brushing, rinse your brush head under
running water with the toothbrush switched on.
Remove the brush head and clean the toothbrush
handle and brush head separately. Make sure
water runs inside the top of the handle as well as
inside the brush head. Wipe all parts dry and let
them air-dry before reassembling your iO
toothbrush again.
Unplug the iOsense™ charger before cleaning.
Clean the charger regularly with a damp cloth only.
Please check individual cleaning instructions for
each accessory in its «Accessories» paragraph.
Accessories (depending on model)
Charging Travel Case (k)
•
To charge your toothbrush (5) place it in the
charging travel case (k) and connect it to the
mains outlet, using the extra power supply (k2)
provided. The power supply may be used for all
global mains voltage ranges (100 – 240V).
•
The flashing light (k1) of the charging travel
case indicates that the toothbrush is charging.
Once the toothbrush is fully charged the light
turns off. A full charge in the charging travel
case typically takes 6 hours.
•
The outer and inner case should be cleaned
with a damp cloth only. Make sure that the
toothbrush and brush head are completely dry
before storing in the travel case.
Note: Clean stains on travel case surfaces immedi-
ately. Store travel case in a clean and dry place.
90277987_UI_booklet_120x170_iO10_MEA_2D.indd 11
90277987_UI_booklet_120x170_iO10_MEA_2D.indd 11
03.03.22 14:46
03.03.22 14:46
