Oracle Sun ZFS Service Manual Download Page 66

Page: 66 / 146

14. Push the release tabs on the side of each rail and slowly push the storage controller into the

rack.

The following image shows the 7420 chassis.

15. Connect the power cords to the power supplies.

16. Verify that standby power is on, indicated by the Power/OK status indicator flashing on the

front panel about two minutes after the power cords are plugged in.

17. Use a pen or other pointed object to press and release the recessed Power button on the

storage controller front panel.

The Power/OK status indicator next to the Power button lights and remains lit. The
Maintenance > Hardware screen of the BUI provides status of the replacement on the Details
page for DIMMs.

7x20

Sun ZFS Storage 7x20 Appliance Customer Service Manual • December 2011 E26399–02

Summary of Contents for Sun ZFS



















































































































































Search results

Summary of Contents for Sun ZFS

Reviews:

Related manuals for Sun ZFS

Brands by name

Popular brands

Oracle Sun ZFS, Service Manual

Search results

Summary of Contents for Sun ZFS

Reviews:

Related manuals for Sun ZFS

Brands by name

Popular brands