Oracle Netra SPARC S7-2 Installation Manual Download Page 94

Page: 94 / 102

Oracle Auto Service Request Software Activation

■

“Configure the Preinstalled OS” on page 86

■

“Reach a State to Install a Fresh OS (Oracle ILOM CLI)” on page 87

■

“Reach a State to Install a Fresh OS (Oracle ILOM Web Interface)” on page 88

■

“Oracle Solaris OS Configuration Parameters” on page 91

■

Oracle ILOM documentation

Oracle Auto Service Request Software Activation

When you have completed initial installation and Oracle Solaris configuration, you can activate

Oracle Auto Service Request (Oracle ASR) software for the server.

Oracle ASR software provides the ability to resolve problems faster by automatically opening

service requests for Oracle's qualified server, storage, and Engineered System products when

specific faults occur.

Parts are dispatched upon receipt of a service request sent by Oracle ASR. In many cases,

Oracle engineers are already working to resolve an issue before you're even aware that a

problem exists.

Oracle products with Oracle ASR securely transport electronic fault telemetry data to Oracle

automatically to help expedite the diagnostic process. The one-way event notification requires

no incoming Internet connections or remote access mechanism. Only the information needed to

solve a problem is communicated to Oracle.

Oracle ASR is a feature of the Oracle hardware warranty, Oracle Premium Support for Systems,

and Oracle Platinum Services.

■

https://www.oracle.com/support/premier/index.html

■

https://www.oracle.com/support/premier/engineered-systems/platinum-services.
html

Oracle ASR is integrated with My Oracle Support (

https://support.oracle.com

). You must

use My Oracle Support to activate your ASR assets, such as a new server.

To activate automated support for a server, download software and find additional information

at:

http://www.oracle.com/us/support/auto-service-request/index.html

Some of resources available for Oracle ASR through that site are:

Netra SPARC S7-2 Server Installation Guide • January 2017

Summary of Contents for Netra SPARC S7-2







































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands

Oracle Netra SPARC S7-2, Installation Manual

Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands