Oracle Netra SPARC S7-2 Installation Manual Download Page 67

Page: 67 / 102

Connect Other Data Cables

Caution -

Do not attach a modem to this port.

Related Information

■

“Available Connections” on page 61

■

“Rear Panel Components (Installation)” on page 15

■

“NET MGT Port” on page 67

■

“10 Gigabit Ethernet Ports” on page 68

■

“USB Ports” on page 69

NET MGT Port

The NET MGT RJ-45 port, located on the rear panel, provides an optional Ethernet connection

to the SP. The service processor network management port uses an RJ-45 cable for a

10/100BASE-T connection. If your network does not use a DHCP server, this port will not be

available until you configure network settings through the SER MGT port. This port does not

support connections to Gigabit networks.

Pin

Signal Description

Pin

Signal Description

Transmit Data +

No Connect

Transmit Data -

Receive Data -

Receive Data +

No Connect

Related Information

■

“Available Connections” on page 61

Connecting Cables

Summary of Contents for Netra SPARC S7-2







































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands

Oracle Netra SPARC S7-2, Installation Manual

Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands