Oracle Netra SPARC S7-2 Installation Manual Download Page 68

Page: 68 / 102

Connect Other Data Cables

■

“Rear Panel Components (Installation)” on page 15

■

“SER MGT Port” on page 66

■

“10 Gigabit Ethernet Ports” on page 68

■

“USB Ports” on page 69

10 Gigabit Ethernet Ports

The server has four RJ-45 10-Gigabit Ethernet (10GbE) network connectors, labeled NET

3, NET 2, NET 1, and NET 0 on the rear panel. Use these ports to connect the server to the

network.

The LEDs located above each NET port are Link/Activity indicators for each port described in

this table.

Connection Type

IEEE Terminology

Transfer Rate

Fast Ethernet

100BASE-TX

100 Mbits/sec

Gigabit Ethernet

1000BASE-T

1000 Mbits/sec

10 Gigabit Ethernet

10GBASE-T

10000 Mbits/sec

Note -

The Oracle ILOM sideband management feature enables you to access the SP using

one of these Ethernet ports. Refer to the

Oracle ILOM Administor's Guide for Configuration

and Maintenance For Release 3.2.x

http://www.oracle.com/goto/ilom321/docs

for

instructions.

Pin

Signal Description

Pin

Signal Description

Transmit/Receive Data 0 +

Transmit/Receive Data 2 -

Netra SPARC S7-2 Server Installation Guide • January 2017

Summary of Contents for Netra SPARC S7-2







































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands

Oracle Netra SPARC S7-2, Installation Manual

Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands