background image

ENGLISH

FRANÇAIS

DEUTSCH

IT

ALIANO

ESP
AÑOL

PORTUGUÊS

EN-1

INSTALLATION INSTRUCTIONS

High Mount

Outdoor Detector

High Mount

Outdoor Detector

HX-40/40AM/

40DAM

HX-40/40AM/

40DAM

• 3.0 m high mount detection area (12 m)

• Unique pyro element

• Intelligent AND logic

• Dual signal processing logic

• Vegetation sway analysis logic

• Ideal detection area setting

• Digital anti-masking (AM/DAM model only)

• Microwave range selector (DAM model only)

CONTENTS

Warning

Caution

Failure to follow the instructions provided with this indication and improper handling may cause 

death or serious injury.

Failure to follow the instructions provided with this indication and improper handling may cause 

injury and/or property damage.

HX-40 

2 PIRs standard model

HX-40AM 

HX-40 with anti-masking

HX-40DAM  HX-40AM with micro-wave

1 INTRODUCTION

  1-1 BEFORE YOUR OPERATION ............................... 1

  1-2 PARTS IDENTIFICATION...................................... 2

  1-3 DETECTION AREA................................................ 3

2 INSTALLATION

  2-1 MOUNTING WITH THE BRACKET........................ 3

  2-2 ADJUSTING THE VERTICAL ANGLE ................... 5

  2-3 MOUNTING WITHOUT THE BRACKET................ 5

  2-4 WIRING .................................................................. 6

  2-5 WALL TAMPER (OPTION)..................................... 6

3 WALK TEST ................................................................. 7

4 SETTING

  4-1 FUNCTION............................................................. 8

5 AREA ADJUSTMENT ................................................ 10

6 LED INDICATION....................................................... 10

7 SPECIFICATIONS

  7-1 SPECIFICATIONS................................................ 11

  7-2 DIMENSIONS....................................................... 11

Mounting height.

Keep the detector parallel to 

the ground. 

Warning

Warning

Caution

Do not repair or modify product 

Keep product away from water

Mount the unit securely

2.5 to 3.0 m

(8.2 to 10 ft.)

Tilt

Parallel

Consider the direction of the 

intruder, for the setting of the 

detection area.

FEATURES

1

INTRODUCTION

1-1

BEFORE YOUR OPERATION

The check 

 mark indicates recommendation.

The nix 

 sign indicates prohibition.

12 m

85°

WIRED MODEL

No.59-2363-3 1711-01

EN

  No.59-2363-2

3.0 m

Summary of Contents for HX-40













Reviews: