background image

ENGLISH

FRANÇAIS

DEUTSCH

IT

ALIANO

ESP
AÑOL

PORTUGUÊS

EN-11

-DETECTION LENGTH ADJUSTMENT

To limit the detection length, apply the appropriate masking seal. Note that there are three different types of seal. 

1
3
2

1

1

2

-AREA MASKING

9.0 m (30 ft.)

3.0 m (10 ft.)

5.5 m (18 ft.)

3.0 m (10 ft.)

4.0 m (13 ft.)

3.0 m (10 ft.)

-HX-40/40AM

DETECTOR CONDITION

LED INDICATOR (RED ONLY)

Warm-up

Blinks for approx. 60 sec.

Alarm

Lights for 2 sec.

Trouble 

output

Anti-Masking 

booting 

(Anti-Masking 

start up)

Blinks 2 times and goes off for 5 sec. and then repeats 

for 180 sec.  

Masking 

detection

Trouble 

output

Anti-Masking 

booting 

(Anti-Masking 

start up)

Masking 

detection

Blinks 3 times and goes off for 3 sec. and then repeats. 

-HX-40DAM

 

Warm-up

Blinks for approx. 60 sec.

Alarm

Red lights for 2 sec.

PIR detection

Green lights for 2 sec.

MW detection

Yellow lights for 2 sec.

Green and Red blink 2 times simultaneously and go off 

for 5 sec. This sequence is repeated for 180 sec.

Green and Red blink 3 times simultaneously and go off 

for 3 sec. This sequence is repeated.

Red

Blink

Light

OFF

Green 

(HX-40DAM only)

Yellow 

(HX-40DAM only)

DETECTOR CONDITION

LED INDICATOR

1

2

3

4

5

6

7

8

9

0

1

9

2

8

3

7

4

6

5

56

Area masking seal

Pasting on example for masking No. 5 and No. 6

5

AREA ADJUSTMENT

6

LED INDICATION

* Specifications and designs are subject to change without prior notice.

Model

Detection method

PIR Coverage

PIR distance limit

Sensitivity

Power input
Current draw
Alarm period

Warm-up period

Alarm output

Tamper output

Trouble output

Aux input

LED indicator

Operating temperature

Environment humidity

Weatherproof

Mounting

Mounting height

Bracket adjust angle

Weight

HX-40DAM

M

A

0

4

-

X

H

0

4

-

X

H

Passive infrared

Passive infrared & Microwave

12 m (40 ft.) 85° wide / 94 zones

4.0 m, 5.5 m, 9.0 m (13 ft., 18 ft., 30 ft.)

2.0°C (3.6°F) at 0.6 m/s

9.5 to 18 VDC

35 mA (max.) 

at 12 VDC

40 mA (max.) 

at 12 VDC

50 mA (max.) 

at 12 VDC

2.0 ±1 sec.

Form C 28 VDC 0.2 A (max.)

N.C. 28 VDC, 0.1 A (max.) N.C. open when cover removed.

-20°C to +60°C (-4°F to +140°F)

95% max.

IP55

Wall

2.5 to 3.0 m (8.2 to 10 ft.)

Vertical: ±20° Horizontal: ±95°

Approx. 60 sec. (LED blinks)

N.C. 28 VDC, 0.1 A (max.)

N.C. 28 VDC, 0.1 A (max.)

Red: Warm-up, 

Alarm

Red: Warm-up, 

Alarm,

Trouble 

Red: 

Warm-up, Alarm, Trouble 
Green: 

Warm-up, PIR detect, Trouble
Yellow:

Warm-up, MW detect

600 g (21.2 oz.)

700 g (24.7 oz.)

Accessories

Bracket, Hood, Area masking seal, Screw (3 × 10 mm) × 2, Screw (4 × 20 mm) × 4

99 (3.90)

205 (8.07)

266 (10.47)

148 (5.83)

197.5 (7.78)

92 (3.62)

Using bracket and hood

Unit: mm (inch)

Without bracket and hood

Unit: mm (inch)

Detectable speed

0.3 m/s to 1.5 m/s (1 ft./s to 5 ft./s)

7-1

SPECIFICATIONS

7-2

DIMENSIONS

7

SPECIFICATIONS

Summary of Contents for HX-40













Reviews: