background image

95

Playback

Playing Back (ZONE 3)

In remote controller operation, while pressing and holding the ZONE 3 SHIFT 

button, press other buttons for operation. Settings are required to playback 

a source in ZONE 3. Set "2. Speaker" - "Configuration" - "Zone Speaker" 

p116

) in the Setup menu to "Zone 2/Zone 3".

1.  While pressing and holding the ZONE 3 SHIFT button on the remote 

controller, point the remote controller at this unit and press  .

• 

"Z3" on the display of the main unit lights up.

2.  While pressing and holding the ZONE 3 SHIFT button on the remote 

controller, press the input selector of the input source you want to play in 

the separate room. To control on the main unit, press the ZONE 3 button, 

and then within 8 seconds, press the input selector button of the input to be 

played in the separate room. To play the same source in the main room and 

separate room, press the ZONE 3 button of the main unit twice.

3.  While pressing and holding the ZONE 3 SHIFT button on the remote 

controller, adjust the volume with the volume button. To do this on the main 

unit, press the ZONE 3

 button, and then within 8 seconds, adjust the volume 

using the MASTER VOLUME dial.

• 

If you turn the unit to standby during multi-zone playback, the Z3 indicator is 

dimmed, and the playback mode is switched to playback in a separate room 

only. Setting ZONE 3 to on while the unit is in standby also switches the 

playback mode to playback in the separate room only.

• 

For ZONE 3 output, audio from externally connected AV components can be 

output only when it is an analog audio signal.

• 

DSD audio signals cannot be output to ZONE 3 with the "NET" input selector.

• 

If ZONE 3 is on, power consumption during standby will increase.

• 

If ZONE 3 is turned on when the Pure Audio listening mode is selected in the 

main room, the mode will automatically switch to the Direct listening mode.

• 

This function turns off if you use the Bluetooth Transmitter ( 

p66

).

To disable the function

: While pressing and holding the ZONE 3 SHIFT button 

on the remote controller, press  .

1

2

Summary of Contents for TX-NR7100
































































































































































































Reviews: