Onkyo TX-NR7100 Instruction Manual Download

Page: 154 / 191

154

Troubleshooting

Power

When the power is turned on, "AMP Diag Mode" appears on the display of the main unit

•

The protection circuit function may have operated. If the unit suddenly enters the standby state and "AMP Diag Mode" appears on the display

of the main unit when the power is turned on again, this function is diagnosing whether or not the main unit is malfunctioning or there is an

abnormality with the speaker cable connection. When the diagnosis is complete, the following messages are displayed.

CH SP WIRE

If the unit returns to the normal ON state after "CH SP WIRE" appears on the display, the speaker cable may have

been short-circuited. After setting the power of this unit to standby state, connect the speaker cable again. Twist the

wires exposed from the tip of the speaker cable so that the wires do not stick out of the speaker terminal.

NG:



If the operation has stopped with "NG" displayed on the display, set the power of this unit to standby state immediately

and remove the power plug from the outlet. The unit may be malfunctioning. Consult a dealer.

The unit turns off unexpectedly

•

If "5. Hardware" - "Power Management" - "Auto Standby" on the Setup menu is activated, the unit automatically enters the standby mode.

•

The protection circuit function may have operated due to an abnormal rise in temperature of the unit. In such a case, the power turns off

repeatedly even if the power is turned on each time. Secure sufficient ventilation space around the unit, wait for a while until the temperature of

the unit decreases. Then, turn the power on again.

WARNING

: If smoke, smell or abnormal noise is produced by the unit, unplug the power cord from the outlet immediately, and contact the dealer or

our company's support.

Audio

•

Make sure that the speaker setup microphone is no longer connected.

• Confirm that the connection between the output jack on the connected device and the input jack on this unit is correct.

•

Make sure that none of the connecting cables are bent, twisted, or damaged.

•

If "MUTING" is displayed on the display and is blinking, press on the remote controller to cancel muting.

•

While headphones are connected to the PHONES jack, no sound is output from the speakers.

•

When "4. Source" - "Audio Select" - "PCM Fixed Mode" on the Setup menu is set to "On", audio is not played if signals other than PCM are input.

Change the setting to Off.

Check the following if the problem persists after you have confirmed the above.

Summary of Contents for TX-NR7100
































































































































































































Search results

Summary of Contents for TX-NR7100

Reviews:

Related manuals for TX-NR7100

Brands by name

Popular brands

Onkyo TX-NR7100, Instruction Manual

Search results

Summary of Contents for TX-NR7100

Reviews:

Related manuals for TX-NR7100

Brands by name

Popular brands