Onkyo TX-NR7100 Instruction Manual Download

Page: 159 / 191

159

Troubleshooting

Tuner

Poor reception or much noise

•

Recheck the antenna connection.

•

Move the antenna away from the speaker cord or power cord.

•

Move the unit away from your TV or PC.

•

Passing cars or airplanes in the vicinity can cause interference.

•

If radio waves are blocked by concrete walls, etc., radio reception may be poor.

•

Change the reception mode to mono (

→

p69

•

When listening to an AM station, operating the remote controller may cause noise. (North American, Australian and Asian models)

•

FM reception may be clearer if you use the antenna jack on the wall used for the TV.

BLUETOOTH function

•

Unplug and plug the power cord of the unit, or turn off and on the BLUETOOTH enabled device. Restart of the BLUETOOTH enabled device

may be effective.

• BLUETOOTH enabled devices must support the A2DP profile.

•

Because a radio wave interference will occur, this unit may not be used near devices such as a microwave oven or cordless phone which use

the radio wave in the 2.4 GHz range.

•

A metallic object near the unit can affect on the radio wave, and BLUETOOTH connection may not be possible.

Check the following if the problem persists after you have confirmed the above.

Cannot transmit from a Bluetooth wireless technology enabled device (PC, smartphone, etc.) to this

unit

•

Check if the BLUETOOTH function of the BLUETOOTH enabled device is enabled.

Cannot connect a BLUETOOTH wireless technology enabled device (PC, smartphone, etc.) to this

unit

•

Initialize the pairing information and perform pairing again.

Firstly delete all the pairing information saved on this unit. In the Setup menu, select "5. Hardware" - "Bluetooth" - "Bluetooth Receiver" - "Pairing

Information", then press ENTER while "Clear" is displayed.

Next, delete the pairing information of this unit that is saved on the BLUETOOTH wireless technology enabled device. For information on how to

clear the pairing information, refer to the BLUETOOTH enabled device's instruction manual.

Finally, perform pairing again. Refer to "Playing audio from BLUETOOTH wireless technology enabled devices with this unit" (

→

p65

) for

pairing instructions.

Summary of Contents for TX-NR7100
































































































































































































Search results

Summary of Contents for TX-NR7100

Reviews:

Related manuals for TX-NR7100

Brands by name

Popular brands

Onkyo TX-NR7100, Instruction Manual

Search results

Summary of Contents for TX-NR7100

Reviews:

Related manuals for TX-NR7100

Brands by name

Popular brands