Onkyo TX-NR7100 Instruction Manual Download

Page: 129 / 191

129

Setup

5. Hardware

2. Network

Change the settings of the Network function.

• When LAN is configured with a DHCP, set "DHCP" to "Enable" to configure

the setting automatically. ("Enable" is set by default) To assign fixed IP

addresses to each components, you must set "DHCP" to "Disable", assign an

address to this unit in the "IP Address" setting, and set information related to

your LAN, such as Subnet Mask and Gateway.

Wi-Fi (Default Value: Off(Wired))

Connect the unit to the network via a wireless LAN router.

•

When switching between "On" and "Off(Wired)", stop the Network service.

Also, when group playback is in process, cancel the group playback once, and

then switch the setting.

Wireless LAN connection

Off(Wired)

Wired LAN connection

Wi-Fi Setup (Default Value: -)

Configure wireless LAN settings by pressing ENTER with "Start" displayed.

Wi-Fi Status (Default Value: -)

The information of the connected access point is displayed.

SSID

SSID of the connected access point.

Signal

Signal strength of the connected access point.

Status

Status of the connected access point.

MAC Address (Default Value: -)

Check the MAC address of this unit.

This value is specific to the component and cannot be changed.

DHCP (Default Value: Enable)

Enable

Auto configuration by DHCP

Disable

Manual configuration without DHCP

•

If you select "Disable", set "IP Address", "Subnet Mask",

"Gateway", and "DNS Server" manually.

IP Address (Default Value: 0.0.0.0)

Displays/Sets the IP address.

Subnet Mask (Default Value: 0.0.0.0)

Displays/Sets the subnet mask.

Gateway (Default Value: 0.0.0.0)

Displays/Sets the gateway.

DNS Server (Default Value: 0.0.0.0)

Displays/Sets the primary DNS server.

Proxy URL (Default Value: -)

Displays/Sets the proxy server URL.

Proxy Port (Default Value: 8080)

Displays/Sets the proxy server port number when you input "Proxy URL".

Summary of Contents for TX-NR7100
































































































































































































Search results

Summary of Contents for TX-NR7100

Reviews:

Related manuals for TX-NR7100

Brands by name

Popular brands

Onkyo TX-NR7100, Instruction Manual

Search results

Summary of Contents for TX-NR7100

Reviews:

Related manuals for TX-NR7100

Brands by name

Popular brands