job
Aid
D
ESCRIPTION
The
Small
Form
‐
Factor
Pluggable
(SFP)
is
a
single
‐
mode
fiber
SFP
that
plugs
into
an
ADTRAN
optical
interface
designed
to
accept
SFPs.
The
SFP
provides
a
single
optical
interface
to
a
physical
interface,
and
is
intended
for
use
with
a
Gigabit
Passive
Optical
Network
(GPON)
Optical
Line
Termination
(OLT)
module.
Installed
into
an
appropriate
module,
the
SFP
provides
a
GPON
interface
to
the
supporting
system.
This
SFP
is
designed
for
use
in
Wavelength
Division
Multiplexing
(WDM)
applications.
This
SFP
has
a
Digital
Diagnostic
Monitoring
(DDM)
function
with
internal
calibration.
The
following
features
are
supported
on
the
SFP:
♦
Data
rate
downstream:
2.488
Gbps
♦
Date
rate
upstream:
1.244
Gbps
♦
Transmit
Wavelength:
1490
nm
♦
Receive
Wavelength:
1310
nm
♦
Optical
distance:
30
km
maximum
♦
Hot
Pluggable
Operational Specifications
♦
Optical
Specifications:
◊
Optical
transmit
level:
+1.5
dBm
to
+5
dBm
◊
Optical
receive
level:
–30
dBm
minimum
◊
Optical
connectors:
SC
♦
Extended
Environmental
Support:
◊
Operational
temperature
range:
–40°C
to
+85°C
◊
Storage
temperature
range:
–40°C
to
+85°C
◊
Relative
humidity
to
95%,
noncondensing
◊
Operating
Altitude
Range:
–197
feet
(–60
meters)
to
13000
feet
(3962
meters)
NOTE
The
operating
ambient
temperature
is
derated
by
1°C/1000
feet
(3.3°C/km).
CAUTION
!
Due
to
compliance
certification
requirements,
only
SFPs
approved
by
ADTRAN
are
to
be
used
with
the
host
module.
ADTRAN
cannot
certify
system
integrity
with
other
SFPs.
I
NSTALLATION
To
install
the
SFP
into
an
appropriate
module,
complete
the
following
steps:
Inspect
the
SFP.
If
damaged,
file
a
claim
with
the
carrier
and
then
contact
ADTRAN
Customer
Support.
CAUTION
!
Do
not
remove
the
protective
end
cap
from
the
SFP
until
the
fiber
optic
cable
is
ready
to
be
connected.
1. Insert
the
SFP
into
the
SFP
cage
on
the
module.
Ensure
the
latch
on
the
SFP
is
facing
upward
for
correct
installation.
2. Slide
the
SFP
all
the
way
into
the
SFP
cage
until
there
is
an
audible
“click”.
NOTE
♦
The
latch
on
the
SFP
is
used
to
remove
the
SFP
from
the
cage
on
the
circuit
card.
♦
The
SFP
meets
or
exceeds
all
the
applicable
requirements
of
NEBS,
Telcordia
GR
‐
63
‐
CORE,
and
GR
‐
1089
‐
CORE.
COMPLIANCE
CAUTION
!
Electrostatic
Discharge
(ESD)
can
damage
electronic
modules.
When
handling
modules,
wear
an
antistatic
discharge
wrist
strap
to
prevent
damage
to
electronic
components.
Place
modules
in
antistatic
packing
material
when
transporting
or
storing.
When
working
on
modules,
always
place
them
on
an
approved
antistatic
mat
that
is
electrically
grounded.
NOTE
♦
The
SFP
is
a
Class
1
Laser
Product
and
complies
with
the
Laser
Safety
requirements
of
FDA
21CFR
1040.10
and
1040.11,
and
EN60825
‐
1
and
‐
2.
The
SFP
is
NRTL
Listed
and
CB
Certified
to
all
applicable
American
and
European
safety
standards.
♦
The
SFP
has
been
evaluated
to
international
safety
standards
EN
60950
‐
1,
AS/NZS
60950.1,
and
IEC
60950
‐
1.
The
SFP
meets
the
requirements
for
CE
marking
under
the
EMC
Directive
and
Low
Voltage
Directive.
Standards
used
to
demonstrate
Compliance
are
EN
300
386,
EN
50222,
EN
55024
as
applicable
and
EN
60950.
CLEI: BVL3AHFD_ _
Product P/N: 1442530G1
Issue Date: April 2010
Document P/N: 61442530G1-22A
Small Form-Factor Pluggable
GPON OLT
Transceiver SFP