background image

 

4

 

Precautions

 

—Continued

 

For British models

 

Replacement and mounting of an AC plug on the power 
supply cord of this unit should be performed only by 
qualified service personnel.

 

IMPORTANT

 

The wires in the mains lead are coloured in accordance 
with the following code:

Blue: Neutral
Brown: Live

As the colours of the wires in the mains lead of this 
apparatus may not correspond with the coloured mark-
ings identifying the terminals in your plug, proceed as 
follows:
The wire which is coloured blue must be connected to 
the terminal which is marked with the letter N or 
coloured black.
The wire which is coloured brown must be connected to 
the terminal which is marked with the letter L or 
coloured red.

 

IMPORTANT

 

The plug is fitted with an appropriate fuse. If the fuse 
needs to be replaced, the replacement fuse must 
approved by ASTA or BSI to BS1362 and have the 
same ampere rating as that indicated on the plug. Check 
for the ASTA mark or the BSI mark on the body of the 
fuse.
If the power cord’s plug is not suitable for your socket 
outlets, cut if off and fit a suitable plug. Fit a suitable 
fuse in the plug.

 

For European Models

 

This unit contains a semiconductor laser system and is 
classified as a “CLASS 1 LASER PRODUCT”. So, to 
use this model properly, read this Instruction Manual 
carefully. In case of any trouble, please contact the store 
where you purchased the unit.
To prevent being exposed to the laser beam, do not try 
to open the enclosure.

 

DANGER:

 

VISIBLE AND/OR INVISIBLE LASER RADIATION 
WHEN OPEN AND INTERLOCK FAILED OR 
DEFEATED. DO NOT STARE INTO BEAM.

 

CAUTION:

 

THIS PRODUCT UTILIZES A LASER. USE OF 
CONTROLS OR ADJUSTMENTS OR PERFOR-
MANCE OF PROCEDURES OTHER THAN THOSE 
SPECIFIED HEREIN MAY RESULT IN HAZARD-
OUS RADIATION EXPOSURE.

The label on the right is 
applied on the rear panel.

 

1. This unit is a CLASS 1 

LASER PRODUCT and 
employs a laser inside the cabinet.

2. To prevent the laser from being exposed, do not remove the 

cover. Refer servicing to qualified personnel.

Declaration  of  Conformity

We, ONKYO EUROPE

ELECTRONICS GmbH
LIEGNITZERSTRASSE 6, 
82194 GROEBENZELL, 
GERMANY

GROEBENZELL, GERMANY

ONKYO EUROPE ELECTRONICS GmbH

K. MIYAGI

declare in own responsibility, that the ONKYO product 
described in this instruction manual is in compliance with the 
corresponding  technical standards such as EN60065, 
EN55013, EN55020 and EN61000-3-2, -3-3.

Summary of Contents for 7555 - DX CD / MP3 Player





























Reviews: