background image

OPERATION

18

LED FAULT CODES  (Flashing LED’s)

One

Two

Three

Four

Eight

Ten 

No Bars

Bars Rippling

CODE   FAULT     SOLUTION

Low voltage shut-off. 

 

   Recharge batteries.

Scrubbing function stops.   

   Check battery connection.

Battery charge level getting low.     Recharge batteries.

Drive motor tripped. 

 

   Reset circuit breaker.

Short circuit to drive motor. 

   Contact Dealer.

Battery lockout. 

 

 

   Recharge batteries immediately.

Controller tripped.   

 

   Contact Dealer.

High battery voltage reading. 

   Check battery connections.

Sleep mode.   

 

 

   Turn key to restore.

Throttle engaged.   

 

   Release directional control bar.

GENERAL MACHINE DIMENSIONS/CAPACITIES

Length    1283mm 

(50.6”)

Width (with squeegee) 

 

762mm (30.0”)

Width (without squeegee)   

554mm (21.8”)

Width (tanks) 

 

 

457 mm (18.0”)

Height 

    1087 

mm 

(42.81”)

Squeegee width 

 

 

762 mm (30.0”)

Scrubbing path 

 

 

510 mm (20”)

Solution Tank capacity 

 

41 L (10.8 gal)

Recovery Tank capacity 

 

41 L (10.8 gal)

Weight empty 

 

 

102 Kg (227 lbs)

Weight with batteries 

 

180 Kg (397 lbs)

SPECIFICATIONS

BATTERIES

System voltage 

 

 

24-V

Number of batteries  

 

Two

Battery voltage 

 

 

12-V

Battery amp hour rating 

 

155AH

Maximium run time  

 

3 hours

Total power consumption   

30A at 22.7 Kg (50 lbs) brush pressure

 

 

 

 

 

37A at 45.3 Kg (100 lbs) brush pressure

Summary of Contents for Striker 2010













































































Reviews: