background image

oneida-air.com

9

Assembly Instructions (Continued)

FIG. 2

2

Align the Latches (G14) onto the holes on 

either side of the Wall Bracket (F) and secure 

them in place using two Pan-Head Screws 

(G15) and Nylock Nuts (G16) [FIG 2]. 

Note: Firmly tighten this hardware. You may 

need to open the latch to access the screw holes 

for mounting.

G16

G14

G15

The wall bracket should be installed to a sturdy, reinforced surface e.g. concrete wall, brick 
wall, drywall with wooden studs. The wall bracket is designed to work with standard 16” stud 
spacing. This template indicates the proper drill holes and the full, assembled size of the wall 
bracket.

Wall Bracket Template

.5"

13 mm

.5"

13 mm

16"

406 mm

8"

203 mm

8"

203 mm

4"

102 mm

4"

102 mm

Supercell Wall Bracket Template

#ZBT040001 

Drill Here

Drill Here

Drill Here

Drill Here

LEVEL THIS LINE

The Cyclone can be rotated in 90-degree increments so that the inlet is facing parallel or 
perpendicular to the wall. Decide how you want your system oriented during installation to 
best meet your shop’s needs. Other positions will not work as they will hinder installation of 
the Rear Support Brace. 

Cyclone Mounting Positions 

RIGHT

FORWARD

LEFT

3

Identify where you will install the Supercell 

in your shop. It must mount to a reinforced 

wall (studs, concrete, etc.) and is designed to 

accommodate standard 16" stud spacing.

Center the wall bracket Template (G1) 

between your wall studs [FIG. 3].

FIG. 3

16"

406 mm

G1

The wall bracket should be installed to a sturdy, reinforced surface e.g. concrete wall, brick 
wall, drywall with wooden studs. The wall bracket is designed to work with standard 16” stud 
spacing. This template indicates the proper drill holes and the full, assembled size of the wall 
bracket.

Wall Bracket Template

.5"

13 mm

.5"

13 mm

16"

406 mm

8"

203 mm

8"

203 mm

4"

102 mm

4"

102 mm

Supercell Wall Bracket Template

#ZBT040001 

Drill Here

Drill Here

Drill Here

Drill Here

LEVEL THIS LINE

The Cyclone can be rotated in 90-degree increments so that the inlet is facing parallel or 
perpendicular to the wall. Decide how you want your system oriented during installation to 
best meet your shop’s needs. Other positions will not work as they will hinder installation of 
the Rear Support Brace. 

Cyclone Mounting Positions 

RIGHT

FORWARD

LEFT

4

Mark a straight level line 26-5/8" from the 

ground. Align the top of the Template (G1) 

with the marked line [FIG. 4] and temporarily 

secure the Template (G1) to the wall with a 

tack or non-marking tape.

FIG. 4

26-5/8"

676 mm

G1

Summary of Contents for Supercell XSK000014

































Reviews: