background image

Page 16

For technical questions, please call 1-800-444-3353.

SKU 68825

3491 Mission Oaks Blvd.  •  PO Box 6009  •  Camarillo, CA 93011  •  (800) 444-3353

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and 

warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 

90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, 

negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and 

tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, 

contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion 

or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS 

WARRANTY IS ExPRESSLY IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE 

WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof 

of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the 

defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot 

readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine 

there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the 

cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Summary of Contents for winter 68825

















Reviews: