background image

Page 13

For technical questions, please call 1-888-866-5797.

Item 63781 
        

Maintenance

  Procedures not specifically explained in this manual must 

be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM PRODUCT FAILURE: 
Do not use damaged products.  If damage is noted, have the problem corrected before further use.

Inspection

MONTHLY,

 inspect the general condition of the Greenhouse.  Check for:

•  loose ratchet tie downs, anchors, tube connections, and rail clamps (tighten as needed)
•  torn or frayed covers, ropes, or cables
•  cracked, bent, or broken parts
•  any other condition that may affect its safe operation. 

Cleaning

1.  Immediately remove any accumulated debris from the cover with a broom, mop, or 

other soft-sided instrument from the outside.  

DO NOT

 use sharp instruments.

2. 

PERIODICALLY,

 clean cover with mild soap and water.  

DO NOT

 use bleach or harsh abrasive products.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LISTS IN THIS DOCUMENT 
AS A REFERENCE TOOL ONLY.  NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY 
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO 
MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS 
OF THE PRODUCT.  IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES 
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND 
LICENSED TECHNICIANS, AND NOT BY THE BUYER.  THE BUYER ASSUMES ALL RISK AND LIABILITY 
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS 
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

SAFETY

ASSEMBL

Y

MAINTENANCE

Summary of Contents for Greenhouse 6 Ft. X 6 Ft.

















Reviews: