19
Installation & Operation Guide: Oncam Grandeye 360
o
Evolution Camera Range
Version 2.4 | January 2014 | Oncam Grandeye, 115 Hammersmith Road, London. W14 0QH. UK
T: +44 (0)20 7371 6640 | E: [email protected] | W: www.oncamgrandeye.com
The enclosure is designed to allow wires to be routed around or over the camera module to the connection points.
The alarm connector (if used) can be removed from the Camera Module to facilitate connection and service.
The Camera Module is installed by attaching and routing the cables, then rotating
the camera into the cleat in the base plate and fastening it in place with the captive
thumb screw. Wires should be routed such that they do not cross over the lens
area when the trim ring is attached.
A BNC video connector is provided for camera testing and providing a spot monitor
output. If used, then check the dip switch settings for either PAL or NTSC video.
Once testing is completed, the BNC test cable can be removed. Then the
dome/trim ring assembly is fastened in place using the four captive security screws
and the provided security driver bit. (Refer to dome handling and cleaning section
for proper procedures on handling the dome bubble).
For installations where the side conduit entry is used for wiring, the sealed plug is removed and a 20mm conduit
connector is used to attach directly to the enclosure. Care must be taken so as not to allow water to run into the
enclosure from the conduit.
4.3.4
Pendant Mounting
For applications that require the enclosure to be mounted below the ceiling plane, the accessory pendant adapter
must be used to adapt the enclosure to 1 ½” NPT female pipe threads. The pendant adapter has a male thread, so
if the installation is to a length of pipe, a female-female coupler needs to be used. Use Teflon pipe tape on pipe
threads to allow compliance, sealing and alignment. Wiring is inside the pipe and enters the enclosure from the
back. The adapter is first mounted to the pipe. Wires are pulled into the enclosure as before. The ceiling base is
then mounted to the pendant adapter using the 4 screws provided.
4.3.5
Wall (Vertical Surface) Mounting
The Evolution housing may be mounted directly to a vertical surface. If the application requires mounting to a
vertical surface but with the housing on a horizontal plane (wall, pole, or building corner) the pendant adaptor and
wall mount is required. The wall mount has a 1½” female pipe thread, allowing the adapter to be directly screwed
into it. There is a set screw in the 1½” thread area which locks the housing into a fixed rotational orientation. Wiring
is fed through the wall mount and adapter to the enclosure.
The wall mount kit fastens to the base plate, a wall mount cleat and the wall mount. and the pendant adapter with
its associated mounting screws. The base plate is used to adapt the wall mount to recessed wiring boxes or to
uneven surfaces. Wiring is passed through the plate. It is then fastened to the mounting surface or box with
appropriate fasteners.
The mounting cleat is then attached to the base plate by placing the cleat over the two threaded studs that protrude
from the plate and fixing it with the nuts provided. It is symmetrical so it can be mounted in either direction. The
wiring is passed through the mount and then the top is hooked over the upper cleat and lowered over the bottom
cleat. The mount is secured to the cleat with the two socket head set screws using a hex wrench.
When mounting to a studded or solid wall and where no electrical box is used, the base plate is not needed. With
this method the cleat plate can be mounted directly to the wall and the wiring is passed through the cleat plate via
the holes provided on either side so that the wire can run on either side of a wall stud if necessary. Likewise, if the
installation is to a pole or corner mount, the base plate is not needed.
4.3.6
Pole or Corner Mounting
The wall mount may be used in conjunction with the accessory pole mount when mounting to a light pole, or to the
corner mount to attach to the corner of a building. The pole mount is a bracket that attaches to a pole 100 to
150mm (4 to 6”) in diameter, with the stainless steel clamping bands provided.
