background image

Through-beam Sensor Heads: FUN Mode Functions

Section 3-8

79

3-8

Through-beam Sensor Heads: 
FUN Mode Functions

3-8-1

Auto-scaling

Select either millimeters or a percentage for the display on the main dis-
play and whether the incident level or intercepted amount is displayed.

The current incident level (intercepted amount) is automatically scaled,
displayed, and output with respect to the reference incident level.

The default display setting is 100-L.

Note 1.

When 100-L or 100-d is selected, the incident level is displayed as a
percentage.

2.

The above table shows values when the monitor focus function is not
used.

3.

When scaling for values other than 5, 10, or 30 mm, use the 2-point
scaling function.

4.

Set the monitor focus after the auto-scale setting.

 Refe

to 

4-5-13 Auto-scale Settings

 for the setting proce-

dure.

Note:

When the auto-scale function is set, all settings are automatically reset to
their default values.

5-L

5-d

10-L

10-d

30-L

30-d

100-L

100-d

Display

5.000

0.000

10.000

0.000

30.000

0.000

100.00

0.00

Linear 
output

+4 V

20 mA

4 V

4 mA

+4 V

20 mA

4 V

4 mA

+4 V

20 mA

4 V

4 mA

+4 V

20 mA

4 V

4 mA

Display

2.500

2.500

5.000

5.000

15.000

15.000

50.000

50.000

Linear 
output

0 V

12 mA

0 V

12 mA

0 V

12 mA

0 V

12 mA

0 V

12 mA

0 V

12 mA

0 V

12 mA

0 V

12 mA

Display

0.000

5.000

0.000

10.00

0

0.000

30.000

0.00

100.00

Linear 
output

4 V

4 mA

+4 V

20 mA

4 V

4 mA

+4 V

20 mA

4 V

4 mA

+4 V

20 mA

4 V

4 mA

+4 V

20 mA

For no interception

Emitter

Receiver

For half interception

Emitter

Sensing object

Receiver

For full interception

Emitter

Sensing object

Receiver

Z157-E1-01C.book  Page 79  Thursday, August 31, 2006  5:13 PM

Summary of Contents for ZX-CAL




























































































































































































Reviews: