Omron ZX-CAL Operation Manuals Download Page 134

Page: 134 / 187

RUN Mode

Section 4-3

114

Incident Level Display

The incident level is displayed.

Resolution Display

The resolution of the linear output is displayed.

This display cannot be selected in Intensity Mode.

POINT

The measured value is displayed on the
main display.

The incident level is displayed on the
sub-display. The display range is 0 to
9999. “P” is displayed in the leftmost
digit. The decimal point is not displayed.

LEFT Key

RIGHT Key

The measured value is displayed on the
main display.

The resolution is displayed on the sub-
display.

“r” is displayed in the leftmost digit.

The display is updated at an approxi-
mately 1-second interval.

LEFT Key

RIGHT Key

The threshold value display is resumed.

Z157-E1-01C.book Page 114 Thursday, August 31, 2006 5:13 PM

Summary of Contents for ZX-CAL




























































































































































































Search results

Summary of Contents for ZX-CAL

Reviews:

Omron ZX-CAL, Operation Manuals, Page: 134 / 187

Search results

Summary of Contents for ZX-CAL

Reviews: