Omron V670 Series User Manual Download Page 143

Page: 143 / 143

Authorized Distributor:

Cat. No. Z148-E1-05

Printed in Japan
0906-0.3M (M)

OMRON Corporation

Industrial Automation Company

Sensing Devices Division H.Q.
Industrial Sensors Division

Shiokoji Horikawa, Shimogyo-ku,
Kyoto, 600-8530 Japan
Tel: (81)75-344-7022/Fax: (81)75-344-7107

Regional Headquarters

OMRON EUROPE B.V.

Sensor Business Unit,
Carl-Benz-Str. 4, D-71154 Nufringen,
Germany
Tel: (49)7032-811-0/Fax: (49)7032-811-199

OMRON ELECTRONICS LLC

1 East Commerce Drive, Schaumburg, IL 60173
U.S.A.
Tel: (1)847-843-7900/Fax: (1)847-843-8568

OMRON ASIA PACIFIC PTE. LTD.

83 Clemenceau Avenue,
#11-01, UE Square,
239920 Singapore
Tel: (65)6835-3011/Fax: (65)6835-2711

OMRON (CHINA) CO., LTD.

Room 2211, Bank of China Tower,
200 Yin Cheng Road (M)
Shanghai, 200120 China
Tel: (86)21-5037-2222/Fax: (86)21-5037-2200

In the interest of product improvement, specifications are
subject to change without notice.

Summary of Contents for V670 Series
















































































































































Search results

Summary of Contents for V670 Series

Reviews:

Related manuals for V670 Series

Brands by name

Popular brands

Omron V670 Series, User Manual

Search results

Summary of Contents for V670 Series

Reviews:

Related manuals for V670 Series

Brands by name

Popular brands