S8VS
Note: 1.
Do not use an inverter output for the Power Supply. Inverters with an output frequency of 50/60 Hz are available, but the rise in the internal
temperature of the Power Supply may result in ignition or burning.
2.
Refer to
Engineering Data (60-W, 90-W, 120-W, 180-W, 240-W, and 480-W Models)
on page 21 for details.
3.
If the output voltage adjuster (V. ADJ) is turned, the voltage will increase by more than +15% of the voltage adjustment range (by more
than +10% for 240-W models). When adjusting the output voltage, confirm the actual output voltage from the Power Supply and be sure
that the load is not damaged.
4.
To reset the protection, turn OFF the input power for three minutes or longer and then turn it back ON.
5.
Displayed on 7-segment LED. (character height: 8 mm)
6.
Resolution of output voltage indication: 0.1 V, Precision of output voltage indication:
±
2% (percentage of output voltage value,
±
1 digit)
7.
Resolution of output current indication: 0.1 A; Precision of output current indication:
±
5% F.S.
±
1 digit max. (specified by rated output
voltage)
8.
Resolution of peak-hold current indication: 0.1 A; Precision of peak-hold current indication:
±
5% F.S.
±
1 digit max. (specified by rated
output voltage);
Signal width required for peak-hold current: 20 ms
9.
A Type and B Type: Sinking, AP Type and P Type: Sourcing
10.
To ensure the emission rating, a ferrite ring core should be used in all cabling (TDK HF60T, HF70RH or equivalent model).
11.
To ensure the emission rating, a ferrite ring core should be used in all cabling (SEIWA E04SR301334 or equivalent model).
Power ratings
60 W
90 W
Type
Item
Standard
Maintenance
forecast monitor
Total run time
monitor
Standard
Maintenance forecast
monitor
Total run time monitor
Efficiency (typical)
78% min.
80% min.
Input
Voltage (See note 1.)
100 to 240 VAC (85 to 264 VAC)
Frequency (See note 1.)
50/60 Hz (47 to 450 Hz)
Current
100-V input
1.7 A max.
2.3 A max.
200-V input
1.0 A max.
1.4 A max.
Power factor
---
Harmonic current emissions
Conforms to EN61000-3-2
Leakage current
100-V input
0.5 mA max.
200-V input
1.0 mA max.
Inrush current
(See note 2.)
100-V input
25 A max. (for a cold start at 25°C)
200-V input
50 A max. (for a cold start at 25°C)
Output
Voltage adjustment range
(See note 3.)
−
10% to 15% (with V. ADJ)
Ripple
2.0% (p-p) max. (at rated input/output voltage)
Input variation influence
0.5% max. (at 85 to 264 VAC input, 100% load)
Load variation influence
(rated input voltage)
1.5% max. (with rated input, 0 to 100% load)
Temperature variation influence
0.05%/°C max.
Startup time (See note 2.)
1,000 ms max. (at rated input/output voltage)
Hold time (See note 2.)
20 ms min. (at rated input/output voltage)
Additional
functions
Overload protection (See note 2.)
105% to 160% of rated load current, voltage drop, intermittent, automatic reset
Overvoltage protection
(See notes 2 and 4.)
Yes
Output voltage indication (See note 5.)
No
Yes (selectable) (See note 6.)
No
Yes (selectable) (See note 6.)
Output current indication (See note 5.)
No
Yes (selectable) (See note 7.)
No
Yes (selectable) (See note 7.)
Peak-hold current indication
(See note 5.)
No
Yes (selectable) (See note 8.)
No
Yes (selectable) (See note 8.)
Maintenance forecast monitor indica-
tion (See note 5.)
No
Yes (selectable)
No
No
Yes
(selectable)
No
Maintenance forecast monitor output
No
Yes (transistor output), 30
VDC max., 50 mA max.
(See note 9.)
No
Total run time monitor indication
(See note 5.)
No
Yes
(selectable)
No
Yes
(selectable)
Total run time monitor output
(See note 5.)
No
Yes
(transistor output), 30
VDC max., 50 mA max.
(See note 9.)
Undervoltage alarm indication
(See note 5.)
No
Yes (selectable)
No
Yes (selectable)
Undervoltage alarm output terminals
No
Yes (transistor output)
30 VDC max., 50 mA max. (See note 9.)
Parallel operation
No
Series operation
Yes for up to 2 Power Supplies (with external diode)
Other
Operating ambient temperature
Refer to the derating curve in
Engineering Data (60-W, 90-W, 120-W, 180-W, 240-W, and 480-W Models)
. (with no icing or condensation)
Storage temperature
−
25 to 65°C
Operating ambient humidity
25% to 85% (Storage humidity: 25% to 90%)
Dielectric strength
3.0 kVAC for 1 min. (between all inputs and outputs/ alarm outputs; detection current: 20 mA)
2.0 kVAC for 1 min. (between all inputs and PE terminals; detection current: 20 mA)
1.0 kVAC for 1 min. (between all outputs/ alarm outputs and PE terminals; detection current: 20 mA)
500 VAC for 1 min. (between all outputs and alarm outputs; detection current: 20 mA)
Insulation resistance
100 M
Ω
min. (between all outputs/ alarm outputs and all inputs/ PE terminals) at 500 VDC
Vibration resistance
10 to 55 Hz, 0.375-mm single amplitude for 2 h each in X, Y, and Z directions
10 to 150 Hz, 0.35-mm single amplitude (5 G max.) for 80 min each in X, Y, and Z directions
Shock resistance
150 m/s
2
, 3 times each in ±X, ±Y, and ±Z directions
Output indicator
Yes (color: green)
EMI
Conducted
Emissions
Conforms to EN61204-3 EN55011 Class A and based on FCC Class A
Conforms to EN61204-3 EN55011 Class B (See note 10.)
Radiated
Emissions
Conforms to EN61204-3 EN55011 Class A
Conforms to EN61204-3 EN55011 Class B (See note 10.)
EMS
Conforms to EN61204-3 high severity levels
Approved standards
UL: UL508 (Listing; Class 2: Per UL1310), UL60950-1
cUL: CSA C22.2 No.14 (Class 2), No.60950-1
EN/VDE: EN50178 (=VDE0160), EN60950-1 (=VDE0805 Teil 1)
SELV (EN60950/EN50178/UL60950-1)
According to VDE0106/P100, IP20
UL: UL508 (Listing), UL60950-1
cUL: CSA C22.2 No.14, No.60950-1
EN/VDE: EN50178 (=VDE0160), EN60950-1 (=VDE0805 Teil 1)
SELV (EN60950/EN50178/UL60950-1)
According to VDE0106/P100, IP20
SEMI
F47-0200 (200-VAC input)
Weight
330 g max.
490 g max.
http://www.ia.omron.com/
5
(c)Copyright OMRON Corporation 2007 All Rights Reserved.
