background image

New S82K

New S82K

8

Item

PFC

No

Yes 

(-P models)

Single output

Dual

outputs

Single output

3 W

7.5 W

7.5 W

15 W

30 W

50 W

90 W

100 W

240 W

240 W

Other

Ambient
temperature

Operating: See the derating curve in the 

Engineering Data section 

(no condensation or icing)

Storage:

–25

°

C to 65

°

C (no condensation or icing)

Ambient
humidity

Operating: 25% to 85%
Storage:

25% to 90%

Dielectric
strength

3,000 VAC at 50/60 Hz for 1 min (between all inputs and outputs)
2,000 VAC at 50/60 Hz for 1 min (between all inputs and GR terminal)
1,000 VAC at 50/60 Hz for 1 min (between all outputs and GR terminal)
Alarm current: 10 mA (3- to 7.5-W models) 20 mA (15- to 100-W models) 25 mA (240-W models)

Insulation
resistance

100 M

 min. at 500 VDC (between all outputs and all inputs/GR terminal)

Vibration
resistance

Malfunction: 10 to 55 Hz, 0.375-mm single amplitude for 2 hrs each in X, Y,
and Z directions

Malfunction: 10 to
55 Hz, 0.15-mm single
amplitude for 2 hrs
each in X, Y, and
Z directions

Shock resistance

Malfunction: 300 m/s

2

, 3 times each in 

±

X, 

±

Y, and 

±

Z directions

Screw tightening
torque

0.74 N 

S

 m max. (see note 2)

Output indicator

Yes (green)

Electromagnetic
interference
(see note 1)

Conforms to FCC class B

Conforms to FCC class A

EMC 
(see note 3, 4)

3 to 100-W Models
(EMI):

EN50081-1

Emission Enclosure:

EN55022 class B (equivalent to EN55011 class B)

Emission AC Mains:

EN55022 class B (equivalent to EN55011 class B)

Emission Output Ports: EN55022 class A (with a recommended optional filter) (see note 3) 
240-W Models
(EMI):

EN50081-2 

Emission Enclosure:

EN55011 class A (see note 4)

Emission AC Mains:

EN55011 class A (see note 4)

Harmonic Current:

EN61000-3-2 (only for S82K-P24024)

Common to All Models 
(EMS):

EN50082-2

Immunity ESD:

EN61000-4-2:

4-kV contact discharge (level 2)
8-kV air discharge (level 3)

Immunity Burst:

EN61000-4-4:

2-kV power-line (level 3)
2-kV output line (level 4)

Immunity Surge:

EN61000-4-5:

between 2-kV lines (except for 240-W models)
between 4-kV line and FG (except for 240-W models)

Approved
standards

Class 2 (UL 1310)/Class 2 (CSA C22.2 No. 950) (see notes 5 and 6) 
UL 508 (Listing)/1950
CSA C22.2 No.14/No.950, EN50178 (VDE0160), EN60950
Conforms to VDE0106/P100

UL 508 (Listing)/1012
CSA C22.2 No.14, CSA
E.B. 1402C, EN50178
(VDE0160), EN60950
Conforms to
VDE106/P100

Weight

150 g max.

260 g
max.

380 g
max.

400 g
max.

600 g max.

1,800 g
max.

2,200 g max.

Note:

1. Defined with a 100% load and the rated input voltage (100 or 200 VAC).

2. Do not press down on the terminal block with a force exceeding 75 N while tightening the terminals.

3. To ensure the emission ratings, a noise filter should be used on the output lines at the closest point. 

(3- to 50-W models: S82Y-JF3-N, 90- and 100-W models: S82Y-JF6-N)

4. To ensure the Emission Enclosure rating, a ferrite ring core should be used on all cables (for S82K-P24024).

5. Models other than dual output models satisfy the Class-2 requirements.

6. To meet Class-2 requirements with the 100-W model, either a fuse or circuit breaker that is UL listed or CSA certified, and rated at

4.2 A max. should be wired in series with the load to be connected to the power supply. Only then can the power supply output be
considered as meeting Class 2.

Summary of Contents for S82K-00305


















Reviews: