background image

50

9. Description of related products

Modem, FAX, or LAN card

Connect to the 

Line/HUB Side

Connect to the 

Modem/TA/Network Card Side

Telephone line, ISDN line, or 10Base-T

* If you do not use the UPS monitoring software, you can disregard this section.

Note 1:  Files cannot be automatically saved.
Note 2:  To automatically stop the UPS, it may be necessary to change the PC’s BIOS settings.

Change the PC’S BIOS settings so that the PC’s power supply is not automatically cut after OS shutdown is performed.

Note 3:  Even if the UPS does not stop when the OS is shut down, it stops automatically when the battery is depleted. 
Note 4:  If the connected PC is an NEC PC-9800 series or PC9821-series computer, use BUC19. 
Note 5:  For the latest information, check our website at http://www.omron.co.jp/ese/

Model

BX35F
BX50F

BX50FW
BX75SW

OS

Communication

method

UPS monitoring

software

Required options

(sold separately)

Serial (USB 1.1)

Serial (USB 1.1)

Windows Server2003

Windows XP/2000

Windows ME/98

PowerAct Pro 
(included software)

UPS service (OS standard) + 
UPS service driver (included software)

PowerAct Pro 
(included software)

Serial (USB 1.1)
(Note 1)

Mac OS X (10.3 or later)
Mac OS X Server (10.3 or later)

UPS Power Manager
(included software)

Serial (RS-232C) 

PowerAct Pro 
(included software)

UPS service (OS standard) + 
UPS service driver (included software)

Contact signal 
(Note 1) (Note 3)

UPS service 
(OS standard)

Contact signal 
(Note 1) (Note 2)

UPS service 
(OS standard)

BUC16, BUC24
optional cable
BUC16 (Note 4), BUC24
optional cable

Serial (RS-232C) 

PowerAct Pro 
(included software)

Serial (RS-232C) 

PowerAct Pro 
(included software)

Windows Server2003
Windows XP/2000

Windows NT4.0

Windows ME/98

Linux(Note 5)

4. Connection example

1. Using the included monitoring software

To use the software, use the “PowerAct Pro” (Windows/Linux), “UPS Power Manager” (Mac) and connect
the PC to the unit using one of the following methods.

BX35F/BX50F (USB connection) ....................... Use the included USB cable to connect

BX50FW/BX75SW (RS-232C connection) ......... Use the included RS-232C cable to connect

9-2 Using the UPS monitoring software

UPS monitoring software selection table

Summary of Contents for POWLI BX35F




























































Reviews: