background image

4

Safety precautions

: Indicates prohibition. For example, 

 indicates that disassembly is prohibited.

: Indicates obligation. For example,  

 indicates that grounding is necessary.

Misuse may cause death or serious injury.

Warning

Caution

Safety precautions

The safety symbols and their meaning used in this manual are as follows:

* Property damage means damage to houses/household effects, livestock, and pets.

Note that events categorized as a caution required matter also may cause more serious results under certain
conditions.

Do not use this unit when very high reliability and safety are required as
listed below. This unit is designed and manufactured for use with OA
equipment such as personal computers.

Medical equipment or system that may cause death directly.

Applications that directly affect the safety of people (For example, the operation and control
of cars and elevators).

Applications in which a failure of the unit may cause significant damage to the society and
public (For example, essential computer systems and main communication equipment.)

Applications with the same level of importance.

Warning

Important information for safe operation is described.
Be sure to read it before installation and start of use.

Misuse may cause injury or property damage.

Carry the unit considering its weight and balance, and place it on a stable
and robust base.

Dropping or toppling the unit may cause injury.

The weight of this unit is approximately: 5 kg (BX35F/BX50F/BX50FW)/ 9 kg (BX75SW).

If you drop the unit, stop using it and have an inspection and repair be done.
For repair, contact us; ____

Keep plastic package bags out of reach of children.

They may put their heads into it, and may be suffocated.

Make sure to connect the AC input plug of the unit into a wall outlet
(commercial power) with rated input voltage.

Connecting to a wall outlet (commercial power) of a different rated input voltage may result in
fire.

The unit may fail.

Caution

 (for installation and connection)

Summary of Contents for POWLI BX35F




























































Reviews: