background image

4

Directions for safe use

Keep packing materials, including plastic bags and film, out of the reach of
children

Should children swallow or put their head into the packing materials, there is danger of suffocation.

Provide secure grounding

Earth the ground terminals of the UPS and devices connected to the UPS. (See "2. Installation
and connection" on page 17)
You may receive an electric shock in the event of trouble or power failure. When both the UPS
and devices are not grounded and you touch both, you may receive an electric shock.

For BN100XR/BN150XR, when you use a 3-pin to 2-pin plug for the AC Input Plug, be sure to
perform grounding before putting the AC Input Plug in a wall outlet (commercial power). On the
other hand, be sure to disconnect the grounding terminal after removing the AC Input Plug from
a wall outlet (commercial power).

Connect the UPS grounding terminal to a grounded-type wall outlet (commercial power) to ensure
that the Power Line Surge Protection works as intended.

Do not use the UPS where the maximum temperature exceeds 40

°

C.

Battery deterioration will occur rapidly.

Doing so may result in a failure or malfunction of the UPS.

Do not exceed the specified ranges in the operating and storage
environments.
Do not install or store the UPS in the following types of places.

Places with high temperatures, low temperatures, or high humidity

Places that receive direct sunlight

Places that are directly heated by a stove or other heat source

Places where the UPS may experience vibration or physical shock

Places where there is dust, corrosive gas, salt, or flammable gas

Outdoors

Placing the UPS in these types of areas may result in malfunction, deterioration, and/or fire.

Do not obstruct the air inlets and outlets on the sides and rear of the UPS.
Do not place the UPS in an enclosed space or cover the UPS.

Doing so may lead to abnormal overheating or fire.

Temperature will increase inside the UPS and may cause a failure of the UPS and battery
deterioration.

Install the UPS 5cm or further away from the wall.

Do not install the UPS in other orientations.
Do not install the UPS on a structurally unsound base.

See "2-2 Installation" on page 20.

If the UPS falls over, or if you drop it, injury may result.

Do not clip the cables, and do not use when the cables are bundled.

If the cables become damaged or overheated, there is a danger of electric shock or fire.

If the cables become damaged, immediately stop using the UPS, and make the necessary
repairs.

Do not connect a device such as a voltage transformer or isolated
transformer to the output side.

Overcurrent may damage the UPS.

Even when connected to the input side, the UPS may fail or malfunction. Make sure to check the
operation before use.

Cautions

 (installation)

Summary of Contents for POWLI BN100XR































































Reviews: