K8DT-AS
13
Recommended Ferrules and Crimp Tools
Recommended ferrules
Note: 1.
Make sure that the outer diameter of the wire coating is
smaller than the inner diameter of the insulation sleeve of
the recommended ferrule.
2.
Make sure that the ferrule processing dimensions conform
to the following figures.
Recommended Flat-blade Screwdriver
Use a flat-blade screwdriver to connect and remove wires.
Use the following flat-blade screwdriver.
The following table shows manufacturers and models as of 2015/Dec.
*
OMRON's exclusive purchase model XW4Z-00B is available to
order as SZF 0-0,4
×
2,5 (manufactured by Phoenix Contact).
• Refer to the contents of this datasheet for cable selection and other
conditions for compliance with EMC standards.
Precaution on EN Standard Compliance
The K8DT complies with EN 60947-5-1 when it is built into a panel,
but observe the following handling methods to ensure compliance
with the requirements of this standard.
Wiring
Overvoltage category III
Pollution degree 2
• Open-frame Device
• If basic, double, or reinforced insulation is required, use the basic,
double, or reinforced insulation defined in IEC 60664 that is
suitable for the maximum applied voltage for the clearance, solid
insulation, and other factors.
• There is basic insulation between the power supply terminals and
input terminals.
• There is basic insulation between the power supply terminals and
output terminals.
• There is basic insulation between the input terminals and output
terminals.
• Operating section must have reinforced or double insulation.
• The sides of the case are not isolated.
• Connect the output contacts (contacts with different polarity) so
that they reach the same potential.
Applicable
wire
Ferrule
Conductor
Length
(mm)
Stripping
length
(mm)
(Ferrules
used)
Recommended ferrules
(mm
2
)
(AWG)
Phoenix Contact
product
Weidmuller
product
Wago
product
0.25
24
8
10
AI 0,25-8
H0.25/12
216-301
10
12
AI 0,25-10
---
---
0.34
22
8
10
AI 0,34-8
H0.34/12
216-302
10
12
AI 0,34-10
---
---
0.5
20
8
10
AI 0,5-8
H0.5/14
216-201
10
12
AI 0,5-10
H0.5/16
216-241
0.75
18
8
10
AI 0,75-8
H0.75/14
216-202
10
12
AI 0,75-10
H0.75/16
216-242
1/1.25
18/17
8
10
AI 1-8
H1.0/14
216-203
10
12
AI 1-10
H1.0/16
216-243
1.25/1.5
17/16
8
10
AI 1,5-8
H1.5/14
216-204
10
12
AI 1,5-10
H1.5/16
216-244
Recommended crimp tool
CRIMPFOX6
CRIMPFOX6T-F
CRIMPFOX10S
PZ6 roto
Variocrimp4
Model
Manufacturer
ESD 0,40
×
2,5
Wera
SZS 0,4
×
2,5
SZF 0-0,4
×
2,5
*
Phoenix Contact
0.4
×
2.5
×
75 302
Wiha
AEF.2,5
×
75
Facom
210-719
Wago
SDI 0.4
×
2.5
×
75
Weidmuller
8 to 10 mm
1.9 mm max.
2.6 mm max.
Side
0.4 mm
2.5 mm dia.
2.5 mm
Front
EN/IEC Standard Compliance
Not isolated
Reinforced insulation
(Double insulation)
Summary of Contents for K8DT-AS Series
Page 14: ...MEMO 14...
