background image

 

10

19.

When cleaning the product, do not use thinners or solvents. Use 

commercial alcohol.

20.

Make sure the power and output indicators operate correctly. 

Depending on the application environment, the indicators and 

other plastic parts may wear prematurely and become difficult to 

see. Check and replace these parts regularly.

21.

The terminal blocks may heat up to 65

°

C. Use care when 

handling them.

22.

Do not use the product if it is accidentally dropped. The internal 

components may be damaged.

23.

Be sure you understand the contents of this catalog and handle 

the product according to the instructions provided.

24.

Do not install the product in any way that would place a load on it.

25.

When discarding the product, properly dispose of it as industrial 

waste.

26.

When using the product, remember that the power supply 

terminals carry a high voltage.

27.

The product must be handled only by trained electrician.

28.

Prior to operation, check the wiring before you supply power to 

the product.

29.

Do not install the product immediately next to heat sources.

Observe the following operating 

methods to prevent failure and 

malfunction.

1.

Use operating power, input power, and other power supplies and 

converters with suitable capacities and rated outputs.

2.

Allow only qualified personnel to manage or handle the product.

3.

Use a precision screwdriver or similar tool to adjust the setting 

knobs.

4.

The distortion in the input waveform for the K8AK-AS, K8AK-AW, 

K8AK-PH, K8AK-PA, K8AK-PM, or K8DS-PH must be 30% max. 

If the input waveform is distorted beyond this level, it may cause 

unnecessary operation.

Do not use the K8AK-VS or K8AK-VW in circuits with waveform 

distortion. Error will be large due to waveform distortion.

5.

Error will be large if the K8AK-AS, K8AK-AW, K8AK-VS, or K8AK-

VW is used for thyristor or inverter control.

The K8AK-PH, K8AK-PA, K8AK-PM, K8AK-PW, or K8DS-PH 

cannot be used on the secondary side of an inverter. To use the 

product on the load side of an inverter, install a noise filter on the 

primary side of the inverter.

6.

To reduce the error in the setting knob, always turn the setting 

knob from the minimum setting toward the maximum setting.

7.

Phase loss is detected for the K8AK-PA or K8AK-PM only when 

the phase loss occurs between the input contacts and the power 

supply. Phase loss is not detected on the load side.

8.

Phase loss can be detected only from the input contacts to the 

power supply side by the K8AK-PH, K8AK-PA, K8AK-PM, or 

K8DS-PH. Phase loss cannot be detected from the input contacts 

to the load side.

Mounting and Removing the K8AK

Mounting to DIN Track

1. Catch the upper hook on the DIN Track.

2. Push the product onto the Track until the hooks lock into place.

To remove the product, pull down on the bottom hook with a flat-

blade screwdriver and lift up on the product.

Mounting and Removing the K8DS

The product may be mounted in any direction, but it must be 

mounted securely and as level as possible.

To mount the product to the DIN Track, hook it on the DIN Track at 

(A) and then press in on the Unit in direction (B).

To remove the product, insert a flat-blade screwdriver at (C) and 

pull down the hook to release the Unit.

Leave at least 30 mm of space between the product and other 

devices to allow easy installation and removal.

Adjusting the Setting Knobs

Use a screwdriver to adjust the setting knobs. The knobs have a 

stopper that prevents them from turning beyond the full right or left 

position. Do not force a knob beyond these points.

* (Not applicable to the K8AK-PH and K8DS-PH.)

Precautions for Correct Use

A

B

PFP-100N (100 cm)

PFP-50N (50 cm)

Applicable DIN Tracks:

(A)

(B)

30 mm min.

(C)

Hook

Setting knob

Summary of Contents for K8AK-AS













Reviews: