Omron H5CX Manual Download Page 18

Page: 18 / 52

Multifunction Digital Timer

H5CX-A/-L (Timer Function)

■

Operating Procedures (Timer Function)

Settings for Basic Functions

Note: All the pins are factory-set to OFF.

Note 1. Be sure to set pin 1 of the DIP switch to ON. If it is set to OFF, the DIP switch settings will not be enabled.

2. Changes to DIP switch settings are enabled when the power is turned ON. (Perform DIP switch settings while the power is OFF.)

3. There is no DIP switch on the H5CX-L8

. For details on the setting methods, refer to page 19.

4. When using time ranges or output modes that cannot be set with the DIP switch, all of the settings have to be made using the operation

keys. For details on the setting methods, refer to page 19.

OFF

Settings for basic functions can be performed with just the DIP switch.

Be sure to set pin 1 to ON when using the DIP switch.

Item

OFF

DIP switch set-
tings enable/
disable

Disabled

Enabled

Time range

Refer to the table on the right.

Output mode

Refer to the table on the right.

Timer mode

Elapsed time
(UP)

Remaining time
(DOWN)

Input signal
width

20 ms

1 ms

Easy Confirmation of Switch Settings Using Indicators

The ON/OFF status of the DIP switch pins can be
confirmed using the front display. For details, refer to page 31.

Pin 2

Pin 3

Pin 4

Time range

0.001 s to 9.999 s

OFF

0.01 s to 99.99 s

OFF

0.1 s to 999.9 s

OFF

1 s to 9999 s

OFF

0 min 01 s to 99 min
59 s

OFF

0.1 min to
999.9 min

OFF

0 h 01 min to
99 h 59 min

OFF

0.1 h to 999.9 h

Pin 5

Pin 6

Output mode

OFF

A mode (signal ON delay
(I): power reset operation)

OFF

A-2 mode: (power ON de-
lay (I): power reset opera-
tion)

OFF

E mode (interval: power
reset operation)

F mode (accumulative:
power hold operation)

Detailed Settings

After making DIP switch settings for basic functions, detailed settings (see note) can be added using the operation keys.
For details, refer to page 19.

Note: Output time, NPN/PNP input mode, display color, key protect level.

Summary of Contents for H5CX





















































Search results

Summary of Contents for H5CX

Reviews:

Related manuals for H5CX

Brands by name

Popular brands

Omron H5CX, Manual

Search results

Summary of Contents for H5CX

Reviews:

Related manuals for H5CX

Brands by name

Popular brands