Omron H5CX Manual Download Page 21 | Manualshive

Page: 21 / 52

background image

Multifunction Digital Timer

H5CX-A/-L (Timer Function)

21

Operation in Run Mode

Present Value and Set Value

These items are displayed when the power is turned ON. The
present value is displayed in the main display and the set value is
displayed in the sub-display. The values displayed will be determined
by the settings made for the time range and the timer mode in func-
tion setting mode.

Present Value and ON Duty Ratio (Output Mode = Z)

The present value is displayed in the main display and the ON duty
ratio is displayed in the sub-display. “SET1” lights at the same time.

Set the ON duty ratio used in ON/OFF-duty adjustable flicker mode
(Z) as a percentage.

If a cycle time is set, cyclic control can be performed in ON/OFF-duty
adjustable flicker mode simply by changing the ON duty ratio.

The output accuracy will vary with the time range, even if the ON
duty ratio setting is the same. Therefore, if fine output time adjust-
ment is required, it is recommended that the time range for the cycle
time is set as small as possible.

Examples:

1. If the cycle time is 20 s, the ON duty ratio is 31%, and the time

range is 1 s to 9999 s, the ON time is given by the following:

20 (s)

´

= 6.2 (s)

®

Rounded off to the nearest integer

(because of the time range setting)

®

ON time = 6 s

2. If the cycle time is 20.00 s, the ON duty ratio is 31%, and the time

range is 0.01 s to 99.99 s, the ON time is given by the following:

20.00 (s)

´

= 6.200 (s)

®

Rounded off to 2 decimal places

(because of the time range setting)

®

ON time = 6.20 s

Present Value and Cycle Time (Output Mode = Z)

The present value is displayed in the main display and the cycle time
is displayed in the sub-display. “SET2” lights at the same time.

Set the cycle time used in ON/OFF-duty adjustable flicker mode (Z).

When Output Mode Is Not Z

Present value

Set value

Set each digit for the set value using the corresponding keys.

Present value

ON duty ratio

Cycle time

When Output Mode Z Is Selected

Present value

Set each digit for the cycle time using the corresponding keys.

Set each digit for the ON duty ratio using the corresponding keys.
(The keys for the 4th digit cannot be used.)

100

ON time = Cycle time

×

ON duty ratio (%)

100

31 (%)

100

31 (%)

Elapsed cycle time

ON duty set as a percentage

Cycle time

ON duty (%)

Output control

Close

Open

Opening/closing valve

Fully closed

↔

Fully open

0%

↔

100%

ON duty

Up/down keys used for analog
adjustment of the ON duty

«
...
19
20
21
22
23
...
»

Summary of Contents for H5CX





















































Reviews:

No comments

Related manuals for H5CX

Brand: Perry Electric Pages: 96

Brand: Orbit Signature Pages: 20

Brand: Sygonix Pages: 6

Brand: Tecnologic Pages: 7

Brand: BROWIN Pages: 18

Ecotimer M Plus 6155

Brand: HRT Pages: 2

Brand: Fagor Pages: 124

Brand: Panasonic Pages: 14

Brand: TFA Pages: 2

Brand: TOGOAL Pages: 2

Brand: Stag Pages: 2

Brand: Perel Pages: 4

Brand: Perel Pages: 4

Brand: Perel Pages: 15

Brand: Perel Pages: 15

Brand: Perel Pages: 15

Brand: Marathon Pages: 5

Brand: JJC Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands