Omron H5CX Manual Download Page 44

Page: 44 / 52

2-stage Digital Timer

H5CX-B

Operating Procedures

■

Setting Set Values

Set values can be set either as offset values (forecast value setting)
or absolute values. Set values are factory-set to forecast value set-
ting.

1. Move to Setting Method Selection Mode by turning ON the power

while pressing both the

Key and

4 Key at the same time.

2. Select forecast value setting (

) or absolute value setting

(

) using the

Keys.

3. When the power is turned ON again, the Timer will start with the

selected setting method.

Note 1: In Setting Method Selection Mode, outputs are OFF and the

timer is stopped.

2: When the setting method is changed, the set values and

present value are reset to 0, and outputs are OFF.

Forecast Value Setting

• OUT1 (forecast output) turns ON when the present value reaches

the forecast value.
The forecast value = set value

forecast set value

The forecast set value is used to set the deviation for the set value.

• OUT2 (control output) turns ON when the present value reaches

the set value.

• If the forecast set value

set value, OUT1 (forecast output) will turn

ON as soon as timing starts.

Absolute Value Setting

• OUT1 (control output 1) turns ON when the present value reaches

set value 1.

• OUT2 (control output 2) turns ON when the present value reaches

set value 2.

Timing stopped

Timing possible

Turn ON the power again.

Turn ON the power while
pressing the Key and
4 Key.

Change the setting method
using Keys 1 to 6.

(Forecast value setting) (Absolute value setting)

Setting Method
Selection Mode

Run Mode

Control output (OUT 2)

Example: F-1 Mode

Forecast
set value

Set value

Forecast value

Present value

Forecast output (OUT1)

Control output 2 (OUT 2)

Example: F-1 Mode

Set value 2

Present value

Control output 1 (OUT1)

Set value 1

Summary of Contents for H5CX





















































Search results

Summary of Contents for H5CX

Reviews:

Related manuals for H5CX

Brands by name

Popular brands

Omron H5CX, Manual

Search results

Summary of Contents for H5CX

Reviews:

Related manuals for H5CX

Brands by name

Popular brands