Omron H5CX Manual Download | Manualshive

Page: 5 / 52

background image

Multifunction Digital Timer

H5CX-A/-L

5

■

Characteristics

Note 1. The values are based on the set value.

2. The value is applied for a minimum pulse width of 1 ms.

3. To meet UL listing requirements with H5CX-L8

@

/-A11

@

models, an OMRON P2CF-08-

@

or P3G-08 Socket must be mounted on the Timer.

Otherwise, H5CX-L8

@

/-A11

@

models are considered to meet UL508 recognition requirements.

4. The Y92S-29 Waterproof Packing and Y92F-30 Flush Mounting Adapter are necessary to ensure IP66, NEMA4, and UL Type 4X water-

proofing between the H5CX and installation panel.

Item

H5CX-A

@

/-A11

@

/-L8

@

Accuracy of operating time
and setting error (including
temperature and voltage in-
fluences) (See note 1.)

Power-ON start:

±

0.01%

±

50 ms max. Rated against set value

Signal start:

±

0.005%

±

30 ms max. Rated against set value

Signal start for transistor output model:

±

0.005%

±

3 ms max. (See note 2.)

If the set value is within the sensor waiting time at startup the control output of the H5CX will not turn ON until the
sensor waiting time passes.

Insulation resistance

100 M

W

min. (at 500 VDC) between current-carrying terminal and exposed non-current-carrying metal parts, and

between non-continuous contacts

Dielectric strength

2,000 VAC, 50/60 Hz for 1 min between current-carrying metal parts and non-current-carrying metal parts
1,000 VAC (for H5CX-

@

SD), 50/60 Hz for 1 min between control output, power supply, and input circuit (2,000 VAC

for models other than H5CX-

@

SD)

1,000 VAC, 50/60 Hz for 1 min between non-continuous contacts

Impulse withstand voltage

3 kV (between power terminals) for 100 to 240 VAC, 1 kV for 24 VAC/12 to 24 VDC
4.5 kV (between current-carrying terminal and exposed non-current-carrying metal parts) for 100 to 240 VAC
1.5 kV for 24 VAC/12 to 24 VDC

Noise immunity

±

1.5 kV (between power terminals) and

±

600 V (between input terminals), square-wave noise by noise simulator

(pulse width: 100 ns/1

m

s, 1-ns rise)

Static immunity

Destruction: 15 kV
Malfunction: 8 kV

Vibration resistance

Destruction: 10 to 55 Hz with 0.75-mm single amplitude each in three directions, four cycles each (8 min per cycle)
Malfunction: 10 to 55 Hz with 0.35-mm single amplitude each in three directions, four cycles each (8 min per cycle)

Shock resistance

Destruction: 294 m/s

2

each in three directions

Malfunction: 98 m/s

2

each in three directions

Life expectancy

Mechanical: 10,000,000 operations min. (under no load at 18,000 operations/h)
Electrical:

100,000 operations min. (5 A at 250 VAC, resistive load at 1,800 operations/h)
See Life-test Curve on page 6.

Approved safety standards
(See notes 3 and 4.)

UL508/Listing, UL50 Type 4X for indoor use (enclosure rating), CSA C22.2 No. 14, conforms to EN61812-1 (Pollution
degree 2/overvoltage category III)
Conforms to VDE0106/P100 (finger protection).

EMC

(EMI)

EN61812-1

Emission Enclosure:

EN55011 Group 1 class A

Emission AC mains:

EN55011 Group 1 class A

(EMS)

EN61812-1

Immunity ESD:

EN61000-4-2:

6 kV contact discharge (level 2)
8 kV air discharge (level 3)

Immunity RF-interference:

EN61000-4-3:

10 V/m (Amplitude-modulated, 80 MHz to 1 GHz) (level 3);
10 V/m (Pulse-modulated, 900 MHz

±

5 MHz) (level 3)

Immunity Conducted
Disturbance:

EN61000-4-6:

10 V (0.15 to 80 MHz) (level 3)

Immunity Burst:

EN61000-4-4:

2 kV power-line (level 3);
1 kV I/O signal-line (level 4)

Immunity Surge:

EN61000-4-5:

1 kV line to lines (power and output lines) (level 3);
2 kV line to ground (power and output lines) (level 3)

Immunity Voltage Dip/Interruption EN61000-4-11:

0.5 cycle, 100% (rated voltage)

Degree of protection

Panel surface: IP66 and NEMA4 (indoors), and UL Type 4X (indoors) (See note 4.)

Weight

H5CX-A

@

: Approx. 135 g, H5CX-A11

@

/-L8

@

: Approx. 105 g

«
...
3
4
5
6
7
...
»

Summary of Contents for H5CX





















































Reviews:

No comments

Related manuals for H5CX

Two Dial Automatic Tap 1017641

Brand: GardenMate Pages: 8

Brand: Kitchen Brains Pages: 4

Brand: Selectric Pages: 4

Brand: BEARWARE Pages: 40

Brand: Orbis Pages: 10

Brand: Zamel Pages: 2

Brand: Anslut Pages: 9

Brand: Radiant Pages: 2

Brand: Safety Technology International Pages: 2

Brand: GE Pages: 2

Brand: Auber Instruments Pages: 4

Brand: finder Pages: 13

Brand: Skytech Pages: 5

Brand: Powerwerx Pages: 2

Brand: Novel Ways Pages: 16

Brand: König Electronic Pages: 92

Brand: Forest Pages: 4

Brand: Avatar Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands