16
F3SG-SR-K
Quick Installation Manual
Troubleshooting Guide Sticker
Attach the included Troubleshooting Guide Sticker nearby, if necessary.
Suitability for Use/Contact Information
TROUBLESHOOTING [EN]
Blinking
㻻㻲㻲
Illuminated
LED indicator
Major cause
E
or
ERR
Blinking Once
O
or
OSSD
Red
Error of OSSD lines
M
or
MAINT
Red
Recoverable error
Red
Replacement-recommended error
Orange
Error of Intelligent Tap
P
or
PNP
Green
Error of internal circuit
F
or
CFG
Green
TOP
Blue
End Cap is not attached. Error of other F3SG in cascade.
On the side of
BTM
Blue
Error of DIP Switch settings of Intelligent Tap
L
or
LONG
Green
E
or
ERR
Blinking Twice
O
or
OSSD
Red
Error due to abnormal power supply or noise
E
or
ERR
S
or
SEQ
Yellow
Input sequence error in Muting, Pre-Reset or PSDI
M
or
MAINT
Orange
Area Beam Indicator (ABI) Orange
Low incident light level (Factory default setting)
On the side of
Error detected during Blanking Monitoring. Error of model
combination in cascade. Faulty F3SG settings.
Error of wiring or DIP Switch setting for Operating Range
Selection
Refer to
Safety Light Curtain F3SG-SR/PG Series User's Manual
.
Suitability for Use
OMRON Corporation
(Manufacturer)
Contact: www.ia.omron.com
Regional Headquarters
Shiokoji Horikawa, Shimogyo-ku, Kyoto, 600-8530 JAPAN
OMRON EUROPE B.V. (Importer in EU)
Wegalaan 67-69, 2132 JD Hoofddorp
The Netherlands
Tel: (31)2356-81-300/Fax: (31)2356-81-388
OMRON ELECTRONICS LLC
2895 Greenspoint Parkway, Suite 200
Hoffman Estates, IL 60169 U.S.A.
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark,
Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
t
F e b , 2 0 2 0
F
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which
apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s
request, Omron will provide applicable third party certification documents identifying ratings and
limitations of use which apply to the Product. This information by itself is not sufficient for a complete
determination of the suitability of the Product in combination with the end product, machine, system, or
other application or use. Buyer shall be solely responsible for determining appropriateness of the
particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY
OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN
DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
Mounting
Wiring
Operation check
