background image

Application Precautions

Section 5

xiii

The operating environment of the PLC System can have a large effect on the
longevity and reliability  of the  system.  Improper  operating  environments  can
lead to  malfunction, failure, and  other  unforeseeable problems  with the PLC
System.  Be  sure  that  the  operating  environment  is  within  the  specified
conditions  at  installation  and  remains  within  the  specified  conditions  during
the life of the system.

Application Precautions

Observe the following precautions when using the CAN Units or the PLC.

Failure to abide by the following precautions could lead to serious or possibly
fatal injury. Always heed these precautions.

  Always  ground  the  system  to  100 

  or  less  when  installing  the  system  to

protect against electrical shock.

  Always turn OFF the power supply to the PLC before attempting any of the

following. Performing any of the following with the power supply turned ON
may lead to electrical shock:

 Mounting  or  removing  any  Units  (e.g.,  I/O  Units,  CPU  Unit,  etc.)  or

memory cassettes.

  Assembling any devices or racks.

  Connecting or disconnecting any cables or wiring.

Failure to abide by the following precautions could lead to faulty operation of
the PLC or the system or could damage the PLC or PLC Units. Always heed
these precautions.

  Use  the  Units  only  with  the  power  supplies  and  voltages  specified  in  the

operation  manuals.  Other  power  supplies  and  voltages  may  damage  the
Units.

  Take measures to stabilise the power supply to conform to the rated supply

if it is not stable.

  Provide  circuit  breakers  and  other  safety  measures  to  provide  protection

against shorts in external wiring.

  Do not apply voltages exceeding the rated input voltage to Input Units. The

Input Units may be destroyed.

  Do  not  apply  voltages  exceeding  the  maximum  switching  capacity  to

Output Units. The Output Units may be destroyed.

  Always  disconnect  the  LG  terminal  when  performing  withstand  voltage

tests.

  Install all Units according to instructions in the operation manuals. Improper

installation may cause faulty operation.

  Provide proper shielding when installing in the following locations:

  Locations subject to static electricity or other sources of noise.

  Locations subject to strong electromagnetic fields.

  Locations subject to possible exposure to radiation.

  Locations near power supply lines.

  Be sure to tighten Backplane screws, terminal screws, and cable connector

screws securely.

  Do not attempt to take any Units apart, to repair any Units, or to modify any

Units in any way.

The following precautions are necessary to  ensure the general  safety of  the
system. Always heed these precautions.

  Provide double safety mechanisms to handle incorrect signals that can  be

generated by broken signal lines or momentary power interruptions.

  Provide external  interlock circuits,  limit circuits,  and  other  safety  circuits  in

!

   Caution

!

   Caution

!

   Caution

!

   

WARNING

Summary of Contents for C200HW-CORT21































































Reviews: