background image

*

7

Remote  Starting

To Remote Start: Press & Release the lower left transmitter button

1) The parking lights will turn on to confirm the starting process.

2) The ignition circuit will turn on.

3) Within a few seconds the parking lights will turn off and the starter will engage.

4) The engine will start, run, and the starter will be disengaged.

5) The parking lights will turn back on while the RS unit is controlling the engine.

6) If the engine stalls, the RS unit will make two attempts to restart it.

When you leave your vehicle, simply set the climate controls for what you de-

sire to be operating upon remote start - heater, defroster or air conditioning.  Upon
entering the vehicle place the ignition key in the switch and turn it to the "On"

THE PARKING LIGHTS

WILL TURN ON, OFF, THE

ENGINE STARTS, THEN

THE PARKING LIGHTS

RESUME ILLUMINATION

To Activate Remote Start:  

Press & Release the lower left

transmitter button

34

Typical Additional

Ignition & Starter

Circuit Optional

Relay Configuration

In cases where an additional Ignition or sec-
ond Starter circuit is present in the
vehicle, configure optional relays
as needed.  This Red 3-pin port
also is used for certain optional
Omega bypass modules for OEM
security systems utilizing
resistors in the ignition
switch or transponders
in the ignition key.

85

86

87a

87

Coil

30

To Additional

Ignition Circuit

Red Wire

Optional

Relay

Fused

constant

12 Volts

Blue Wire

85

86

87a

87

Coil

30

To Additional

Starter Circuit

Green Wire

Fused

constant

12 Volts

Optional

Relay

The wires
used and
the power
source for
the optional
relays must be
capable of supplying
and carrying high
amperage.

Summary of Contents for RS-7K2





















Reviews: