background image

36

The RS-7K2 has six programmable features. These features can be changed
using the transmitter when the unit is in Features Programming Mode.  These six
features, their default and optional settings, are:

 Programmable  Features

#

FEATURE

          DEFAULT

  OPTION

#

1 Doors Lock/Unlock Upon Ignition On/Off

       ON

    OFF

#

2 Door Lock Pulse Duration

.75 Second

      3 Seconds

#

3 Single Or Double Unlock Pulse

    Single

  Double

#

4 Engine Running Time

 15 Minutes

30 Minutes

#

5 Starter Cranking Time (in seconds)

 .8, 1.2, 1.5

1.2, 1.5, 2

#

6 1 Or 2 Pulse Remote Start Activation

   1 Pulse

  2 Pulses

To access Features Programming Mode and changing features:

1) Turn the ignition switch “On”, then “Off”.

2) Within 7 seconds flip the Valet Switch “on” and “off” 5 times.  The parking lights

flash once indicating Features Programming Mode.

5

To Lock the Vehicle's Doors:  Press & Release the upper left
transmitter button

Locking  &  Unlocking  the  Doors

To Unlock the Vehicle's Doors:  Press & Release the upper right
transmitter button

- The parking lights will flash twice to confirm and the doors will unlock.

THE PARKING

LIGHTS WILL FLASH

ONCE

THE DOORS WILL LOCK

- The parking lights will flash once to confirm and the doors will lock.

*

THE PARKING

LIGHTS WILL FLASH

TWICE

THE DOORS WILL UNLOCK

*

Summary of Contents for RS-7K2





















Reviews: