background image

Installation Considerations

BEFORE STARTING THE INSTALLATION, READ THIS ENTIRE 

MANUAL TO DETERMINE INSTALLATION REQUIREMENTS

• 

VERIFY EACH CIRCUIT WITH A DIGITAL MULTIMETER

• 

IDENTIFY REQUIRED CIRCUITS FOR THE VEHICLE

• 

TAPE OFF OR REMOVE ANY UNUSED WIRING TO PREVENT    

  POSSIBLE SHORT CIRCUITS

• 

ONLY ACTIVATE THE REMOTE START FUNCTION IN A WELL  

 

  VENTILATED ENVIRONMENT

• 

AFFIX THE UNDERHOOD WARNING STICKER

•  AVOID ANY AIRBAG CIRCUITS, USUALLY INDICATED BY A  

 

  YELLOW SLEEVE OR JACKET AROUND THE WIRING

6 Pin Main Wire Harness

RED & RED/WHITE WIRES - CONSTANT POWER (+) INPUT

  REQUIRED. 

These wires provide the constant positive 12v power supply for the 

system’s operation. 

CONNECTION: 

Connect these to a co12 volt supply 

with sufficient amperage for remote starting. The +12v supply to the ignition switch 

is ideal. Some vehicle’s have low amperage ignition switches in which case you 

would need to find a power supply at a fuse block or at the vehicle’s battery. Fuse 

these wires within 6 inches of the connection to the vehicle. The two 30AMP fuses 

in the harness protect the system module, NOT THE VEHICLE. It is ideal to have  a 

separate supply for each wire but, if the chosen supply is sufficient enough, you can 

combine both wires at the same point.

  Most of the main wiring harness connections are high amperage circuits so it is 

recommended to direct splice, solder, & adequately insulate each connection. Many 

of these connections are made at the vehicle’s ignition switch so be sure to properly 

route the harness away from anything that could compromise the wire insulation. 

The goal is to mimic the ignition switch. Keep this in mind when deciding which igni

-

tion & accessory circuits to power. 

 

NOTE: A low current harness for newer vehicles is available. It has 18 gauge, 

100% copper wires and the RED & RED/WHITE wires are fused at 10A each. 

Order P/N: H-RS6BLC

PINK WIRE - IGNITION/

ACC

/

START

 (+) INPUT/OUTPUT

  REQUIRED. 

This connection is required & is critical to the operation of the sys

-

tem. It is an “IGNITION ON” input when the ignition key is turned on. By default, it is 

the primary ignition output for remote start operation. It turns on when remote start is 

activated & stays on during engine cranking for the entire remote start sequence. 

CONNECTION:

 Use any IGNITION, ACCESSORY, or secondary START circuit 

in the vehicle. This wire is defaulted for IGNITION output though it may change 

through the VEHICLE LEARN process (p.10) to match the connected vehicle circuit.

3

Summary of Contents for Excalibur RS-X70













Reviews: