background image

Window Mount Antenna Module

 

Be sure to clean the glass before adhering the antenna. Mount it high in the windshield avoid

-

ing metal parts of the vehicle . Metal based window tint can decrease performance. Route the 

harness to the antenna module avoiding sharp objects that could compromise the harness jacket.

Vehicle Learn

  Vehicle Learn is a procedure that allows you to quickly configure all vehicle dependant features. 

It also serves as a diagnostic tool for your IGN/ACC/START output connections on the main power 

harness. It’s much faster than programming, saving you valuable time, & helps you discover critical 

mistakes.  

 

VEHICLE LEARN WILL:

• 

Detect the function of the PINK, PINK/WHITE, and ORANGE wires to automatically change 

the outputs to match the vehicle.

• 

Diagnose the PINK, PINK/WHITE, ORANGE, & VIOLET wire connections.

• 

Let you quickly choose engine type 

• Auto-select Data-tach, tach wire, or tachless modes.

• Auto-select data port protocols

• Save tons of time in the bay!

BEFORE YOU BEGIN:

• Make all wire connections

• Connect any accessories/modules to the data ports.  

If you are using an interface module/bypass kit, make sure it is in “DATA 

 

MODE” and programmed to the vehicle. 

• Set the parking brake if it is connected to the BLACK/WHITE wire.

Step 1: Turn the ignition key ON 

(do not start)

Step 2: Activate remote start by the remote, input activation wire, or smartphone control. 

The system will chirp/flash lights to indicate engine type (Default: 1x = Gasoline). 

Step 3: Press valet to change engine type, if needed:  

The system will chirp/flash lights to confirm each selection.

 

1 chirp=Gasoline, 2 chirps=Diesel 15, 3 chirps=Diesel 20, 4 chirps=Diesel 30

Step 4: Start the engine with the ignition key

Step 5: Turn the ignition key OFF

 

The system will chirp/flash lights the # of IGN/ACC/START circuits detected (Max: 4x). 

 

EXAMPLE:

 If you connected the PINK, VIOLET, & ORANGE wires, the system should 

chirp 3x. If it only chirps 2x, one connection has a problem and should be checked. 

Then start over at Step 1 to retest.

Step 6: Within 20 seconds of Step 5, Activate remote start. Wait until engine is running 

and LED is flashing slow.

 

The system will poll both data ports for modules using the DBI protocol. If they do not 

respond, it will automatically switch to iDatalink protocol.  

- After the engine is running, the system will look for data tach & tach wire availability. If  

detected, the system will switch to that method. If not, it will remain in tachless-hi.

  Some models are equipped with a motion sensor that provides added protection for remote 

start by shutting down the engine if motion is detected during the START output. This is ideal for 

manual transmission vehicles and eliminates the need for performing ‘manual transmission setup’ 

by the user. If the sensor is present, a “3D” logo will be on the antenna case. 

3D Motion Sensor

10

Summary of Contents for Excalibur RS-X70













Reviews: