background image

Wiring Overview Diagram

14 PIN HARNESS

Remote Start Activation (-) In  -  WHITE/BLUE

Starter Interrupt (-) Out  -  ORANGE

3

Alarm Ign. Control (+)  -  YELLOW

Flashing Light (-) Out  -  WHITE/BLACK

OEM Arm (-) Out  -  LT. GREEN/RED

3

Trunk Release/CH2 (-) Out  -  RED/WHITE

System Ground (-) In  -  BLACK

OEM Disarm (-) Out  -  LT. GREEN/BLACK

3

Horn (-) Out  -  BROWN

Hood Trigger (-) In  -  GRAY

Brake (+) In  -  BROWN/RED

Tach In  -  VIOLET/WHITE

Flashing Light (+) Out  -  WHITE

Neutral Safety (-) In  -  BLACK/WHITE

10 AMP

30 AMP

30 AMP

WIRE LEGEND

HARD WIRE CONNECTION REQUIRED 
FUNCTION SUPPORTED VIA DATA PORTS

OPTIONAL STARTER 

INTERRUPT SOCKET & RELAY

To Starter

To Ignition Switch

WHITE

RED

Cut Starter 

Wire

ORANGE

NOTES

1.  LOW CURRENT HARNESS P/N: H-RS6BLC Available 

for vehicles with less than 20A ignition switches. 

2.  Learning output - see Vehicle Learn Procedure

3.  Programmable output - see feature chart

6 PIN POWER HARNESS

1

Constant 12v (+) In  -  RED/WHITE

Ignition #2 (+) In/Out  -  PINK/WHITE

2

Constant 12v (+) In  -  RED

Start (+) In/Out  -  VIOLET

Ignition #1 (+) In/Out  -  PINK

2

Accessory (+) In/Out  -  ORANGE

2

6

Summary of Contents for Excalibur RS-X70













Reviews: