Olympic Medical BILI-LITE 33 Instruction Manual Download Page 9

Page: 9 / 56

OLYMPIC BILI-LITE

Model 33/34 Instruction Manual

1-3

Intended Use

Intended Use

The Olympic Bili-Lite

Model 33/34 is a floorstand phototherapy light intended to

provide therapeutic irradiance to treat neonatal hyperbilirubinemia.

Description

The Olympic Bili-Lite Model 33/34 is a floorstand phototherapy light (see

Figure 1.1). Its light hood is height adjustable from 43 to 59 in. (110 to 151 cm)
above the floor. The Bili-Lite Model 34 includes an Olympic Bili-Timer

The Bili-Lite is equipped standard with eight Olympic Blue (Type OB) fluorescent
bulbs. Other types of fluorescent bulbs are available (see

Parts and Accessories

page 7-1).

Figure 1.1

Bili-Lite Model 33/34

Hood tilt attachment

(optional accessory for

Model 33/34)

Support post

Base

Light hood

Safety shield

Caster wheels

Height adjustment knob

Power cord

Summary of Contents for BILI-LITE 33

























































Search results

Summary of Contents for BILI-LITE 33

Reviews:

Brands by name

Popular brands

Olympic Medical BILI-LITE 33, Instruction Manual

Search results

Summary of Contents for BILI-LITE 33

Reviews:

Brands by name

Popular brands