manualshive.com logo in svg

Olympic Medical BILI-LITE 33, Instruction Manual

Share
Download
Olympic Medical BILI-LITE 33 Instruction Manual Download Page 38

6-8

OLYMPIC BILI-LITE 

Model 33/34 Instruction Manual

Repair Procedures

 

Replacing the Bulb Holder

If the power is on and the fan runs but a bulb does not light, replace the bulb holder.

Required Items:

„

Bulb holder assembly replacement kit (part no. 200018)

„

3/8-in. nutdriver

„

5/16-in nutdriver

„

Medium-size Phillips-head screwdriver

„

Metal snippers

„

Loctite

®

222 (red)

To replace the bulb holder:

1

Press the power switch to the 

OFF

 (O) position, then unplug the power cord.

2

Remove the safety shield: First, remove the two retaining screws and washers. 

Next, slide the safety shield out.

3

Rotate each bulb out of its socket; set the bulbs aside in a secure place.

4

Remove the light hood from the support post (see page 6-5).

5

Remove the fan shroud: Loosen and remove the three Phillips-head screws 

and washers.

6

Remove the safety shield bracket: Loosen and remove the two acorn nuts and 

two Phillips-head screws and washers.

7

Remove the reflector:

a

Remove the four nuts and washers securing the reflector to the light hood 

(see Figure 6.3 on page 6-6).

b

Starting at one corner, carefully pull the reflector away from the hood. Pull 

the sides of the hood outward slightly to allow the reflector to clear the 

shield tab.

c

Once the reflector is clear of the hood, unplug wires 5 and 22 from the 

power switch, then unclip wires 5 and 22 from the clip centered on the 

inside the hood (see

 

Figure 6.4). It may be possible to lay the reflector down 

next to the hood to work on the bulb holder. (In older models, cut the wires 

or otherwise detach them.)

8

Remove the bulb holder:

a

Remove the 6x32 nut and washer centered on top of the bulb holder, then 

pull off the bulb holder cover (see

 

Figure 6.5).

b

Remove the connector screws, then slide the two connectors off of the bulb 

holder (see

 

Figure 6.5).

c

Lift off the bulb holder.

CAUTION

„

The light hood is heavy. Installing or removing the light hood requires two people.

„

Tighten the support post height adjustment knob firmly before attempting to remove the 
light hood.

Summary of Contents for BILI-LITE 33

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands