manualshive.com logo in svg

Olympic Medical BILI-LITE 33, Instruction Manual

Share
Download
Olympic Medical BILI-LITE 33 Instruction Manual Download Page 39

OLYMPIC BILI-LITE 

Model 33/34 Instruction Manual

6-9

Repair Procedures

 

Figure 6.5

Bulb holder and cover

To install the new bulb holder:

1

Install the new bulb holder:

a

Place the new bulb holder into position.

b

Slide the two connectors under the connector screws, then tighten 

the screws.

Figure 6.6

Resizing the connector for older models

c

Place the bulb holder cover over the bulb holder. Place a drop of Loctite 222 

on the screw, then place the washer and tighten the nut to secure the cover 

(see

 

Figure 6.5 on page 6-9).

2

Place wires 5 and 22 into the clip centered on the inside the hood.

3

Insert the reflector into the hood.

4

Place the washers, then tighten the nuts that secure the reflector to the 

light hood.

5

Attach the fan shroud: Tighten the three Phillips-head screws and washers.

6

Attach the safety shield bracket: Tighten the two acorn nuts and two 

Phillips-head screws and washers.

Ballast

Red connector

Connector screw

Bulb holder cover screw

Nut

Bulb holder cover

Black connector

Connector screw

Bulb holder

Starter

Starter socket

NOTE

#

The new bulb holder has a tighter area for the red connector. In older devices, to prevent 
the bulb holder from cracking as the screw is tightened, it may be necessary to shorten 
both tines of the red connector by 1/8 in. (0.3 cm)(see

 

Figure 6.6).

Original length tine

Tine shortened 1/8 in.

Summary of Contents for BILI-LITE 33

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands