OLT SunShed Garden Shed SSGS1212-FJ-METAL Assembly Manual Download | Manualshive

Page: 36 / 45

background image

75.

Attach

Door Handle, Exterior Barrel Bolt

and

Interior Barrel Bolt

to door. Handle is

positioned on top door, Barrel Bolt on bottom door, and Interior Barrel Bolt (silver) on top door stud.
Attach Black Barrel Bolt as illustrated above with 3/4” Black Screws. Note how female part of Barrel
Bolt is positioned higher than male part. Do a dry run first to position Barrel Bolt correctly.

Important:

Drill pilot holes with 1/8” drill bit prior to securing to prevent wood from splitting.

74.

Place the Top Dutch Door Panel into place

and gap top and bottom trims on the outside
about 1/8” apart. On the inside, horizontal door
frames should be about 1/4” apart. Use a shim
once again to help you. Attach hinges to trim
with 2” black headed screws provided.

Slight gap.Top Trim overlaps
bottom trim to prevent water
from getting in.

Bottom Skirting

72.

Attach Door Hinges to

Top

and

Bottom Dutch Door

sections. Top Door has trim overhanging

door at bottom while bottom door has trim recessed slightly. Hinges should be centered on door trim
with barrel nudged to end of trim. Use 2” & 3/4” black headed screws as shown above.

73.

Place Bottom Dutch Door panel into position.

Gap 3/8” on bottom, evenly space on sides, and
attach hinge to doorway seam trim with 2” black
headed screws. Use shim to help keep the door
evenly spaced on bottom. One of the extra roof
shingles (see parts list) can be used.

Bottom Door

3/8” gap at bottom.
Evenly spaced on
sides.

3/4” screw

Doorway Seam

T

rim

2” Black
Screws

Top and Bottom
Hinges centered
on door trim.

Top Door Trim

Bottom Door Trim

Middle Hinges
centered on trims.

2“ Screws

Temporarily position
Interior Door Stop to
help align Interior
Barrel Bolt.

Top Door

Bottom Door

1/4” gap on
inside.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 36

«
...
34
35
36
37
38
...
»

Summary of Contents for SunShed Garden Shed SSGS1212-FJ-METAL














































Reviews:

No comments

Related manuals for SunShed Garden Shed SSGS1212-FJ-METAL

WW-96 FSC Mix FRA19-2121FSC

Brand: Palmako Pages: 53

HEARTLAND 16985

Brand: Backyard Products Pages: 76

Brand: Dancover Pages: 65

Brand: Keter Pages: 40

Extension LAZA28-1624

Brand: Palmako Pages: 51

Brand: Karibu Pages: 35

Brand: Karibu Pages: 36

Brand: Palmako Pages: 103

GS84-SLIDER-METAL-AK

Brand: OLT Pages: 38

Brand: Palmako Pages: 65

Brand: Palmako Pages: 63

Brand: Weka Pages: 96

Brand: Bear County Pages: 28

BOURNEMOUTH 03BRN0807-V4

Brand: Mercia Garden Products Pages: 7

Greenbriar II 12x16

Brand: Best Barns Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands