background image

17.

 With the corner wall  

attachment complete, position a 
Solid Rear Wall Panel so  
bottom 2x3 wall framing is  
sitting flush with outside floor 
frame. Wall siding should  
overhang floor by approximately 
1/2”.   Attach  rear wall panel 
studs together as per 

Step 14

.

Rear Solid W

all

2x3 wall framing flush with 
outside of floor frame.

16.

  Position Window Trim around window doing a dry run first and attach with 4 - 1 1/2” finishing nails 

per piece. There are two Trim Kits (Regular / Narrow). The regular window kit = 1 x 24 1/16” = top (angle 
cut on ends) / 3 x 23” = Sides & Bottom. Narrow window kit = 1 x 19 7/8” Top, 2 x 21 7/16” Sides,  
1 x 18  3/4” Bottom.  Window trim has a small dado on reverse face. Outside flange of window will 
roughly sit in the dado to give a better fit. 

T

rim Dado

Trim dado 
sits in flange.

15.

  Locate 

Window Inserts for Double Window Walls

. Before installing, dab caulk in channel  

on both sides of window opening. This will prevent water from getting in behind window.  Position window 
in cavity. 

Important: 

Pre-drill holes in filler strip at top of window with 1/8” drill bit before fastening window 

inserts. Secure with 8 - 1 1/4” screws. .Caulk gap between siding and window at top. This requires a 
large amount of caulking but is important to fill. Later, Window Trims will be installed to hide caulking.  
Complete Window Inserts as walls are erected or complete in 

Step 23.

Caulk 

channel in siding 

on both sides of 

window. 

Note:

 We recommend you wait to 

install the windows last, so they don’t 
get damaged during construction.

Important:

 Lineup window insert in 

cavity and 

pre-drill 

holes into the 

filler strip at the top of the window.

Filler strip

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 12

Summary of Contents for SunShed Garden Shed SSGS1212-FJ-METAL














































Reviews: